WF520ABP ((XAC)(0003)) Samsung Washer - Overview

Sections of the WF520ABP

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Drain Pump Assembly - 120V 60Hz – Part Number: DC31-00054A
Drain Pump Assembly - 120V 60Hz
★★★★★
★★★★★
(17)
PartSelect #: PS4204638
Manufacturer #: DC31-00054A
This is a 120 volt, 60 hertz drain pump assembly for a washing machine. It is a genuine OEM part. This pump helps expel water from the washing machine, and is activated after the spin speed is maintai...
$162.61
  In Stock
Order within the next 8 hrs and your part ships today!
Hex Head Bolt – Part Number: DC60-40137A
Hex Head Bolt
★★★★★
★★★★★
(1)
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
$14.23
  In Stock
Order within the next 8 hrs and your part ships today!
Shock Damper Front – Part Number: DC66-00470A
Shock Damper Front
★★★★★
★★★★★
(3)
PartSelect #: PS4212219
Manufacturer #: DC66-00470A
This is an individually sold front shock absorber designed for use with Samsung dryers. Shock absorbers are used to distribute the weight of the dryer drum evenly and ensure that the different bumps a...
$66.88
  In Stock
Order within the next 8 hrs and your part ships today!
Door Switch Assembly – Part Number: DC64-00519B
Door Switch Assembly
★★★★★
★★★★★
(3)
PartSelect #: PS4210737
Manufacturer #: DC64-00519B
This is a door switch assembly designed for Samsung washing machines. This door switch assembly is used to latch and lock the door shut before the washing cycle commences and communicates with the con...
$33.38
  On Order
Outer Seal Clamp – Part Number: DC97-04973B
Outer Seal Clamp
★★★★★
★★★★★
(3)
PartSelect #: PS4218211
Manufacturer #: DC97-04973B
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made o...
$14.89
  On Order
Water Inlet Valve – Part Number: DC62-30314K
Water Inlet Valve
★★★★★
★★★★★
(2)
PartSelect #: PS4209100
Manufacturer #: DC62-30314K
One solenoid valve for hot water
$89.62
  In Stock
Order within the next 8 hrs and your part ships today!
Screw - Tapping – Part Number: 6002-000213
Screw - Tapping
PartSelect #: PS4133148
Manufacturer #: 6002-000213
$4.66
  In Stock
Order within the next 8 hrs and your part ships today!
Assembly Fixer Tub – Part Number: DC97-14489R
Assembly Fixer Tub
★★★★★
★★★★★
(1)
PartSelect #: PS16224595
Manufacturer #: DC97-14489R
Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in pl...
$42.49
  In Stock
Order within the next 8 hrs and your part ships today!
Rear Tub Oil Seal – Part Number: DC62-00156A
Rear Tub Oil Seal
PartSelect #: PS4208679
Manufacturer #: DC62-00156A
$34.57
  In Stock
Order within the next 8 hrs and your part ships today!
Washer Bolt Assembly – Part Number: DC97-02412A
Washer Bolt Assembly
PartSelect #: PS4217876
Manufacturer #: DC97-02412A
Assembly BOLT;SWF-P12,MOTOR/
$23.80
  In Stock
Order within the next 8 hrs and your part ships today!
Door Glass – Part Number: DC64-00504C
Door Glass
★★★★★
★★★★★
(2)
PartSelect #: PS4210731
Manufacturer #: DC64-00504C
$161.42
  In Stock
Order within the next 8 hrs and your part ships today!
Water Temperature Thermistor – Part Number: DC90-10128N
Water Temperature Thermistor
★★★★★
★★★★★
(1)
PartSelect #: PS4214274
Manufacturer #: DC90-10128N
The thermistor monitors and helps regulator the water temperature in the washer.
$51.33
  In Stock
Order within the next 8 hrs and your part ships today!

Questions And Answers for WF520ABP

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the WF520ABP

[Viewing 3 of 3]
Will not drain
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing
Show All
Leaking
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Code indicating washer was NOT discharging water
Watched the video, procedure was simple and as depicted on the video. Started by using a wet shop Vac to the discharge hose and sucked as much dirty wash water out as possible. Removed the pump,and found the motor did not turn freely. Removed the motor (3 screws) and replaced the motor with new part. Reassembled the washer, everything worked as it should. After about 3-4 loads of laundry, the "Not Draining" code / problem returned. Again, sucked out the water with the Shop Vac. Checked the Filter /Cleanout and found it completely packed with MUD. Cleaned that out, and again disassembled the washer. The pump was removed and the remaining muddy gunk was cleaned from the impeller. The 3 drain lines that attached to the pump were inspected for blockage/obstruction and flushed of any muddy residue. Reassembly was quick and easy, and the washer has worked well since. I have no idea how the dirt got into the system with enough dirt to gunk up the system. Recommend keeping more frequent inspections of the cleanout trap.
Parts Used:
Drain Pump Assembly - 120V 60Hz
  • SCOTT from VERNAL, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
8 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water level was lower than normal.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wire tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
Parts Used:
Washer Water-Level Pressure Switch
  • Fredric from ROCKMART, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer making noise a snow smoking.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
Parts Used:
Hex Head Bolt
  • Samuel from NEEDVILLE, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench set
12 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!