Models
>
WF219ANB/XAA
WF219ANB/XAA Samsung Washer - Overview
Sections of the WF219ANB/XAA
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Drain Pump Assembly - 120V 60Hz
PartSelect #: PS4204638
Manufacturer #: DC31-00054A
This is a 120 volt, 60 hertz drain pump assembly for a washing machine. It is a genuine OEM part. This pump helps expel water from the washing machine, and is activated after the spin speed is maintai...
$181.80
In Stock
Hex Head Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
$11.94
In Stock
Shock Damper Front
PartSelect #: PS4212219
Manufacturer #: DC66-00470A
This is an individually sold front shock absorber designed for use with Samsung dryers. Shock absorbers are used to distribute the weight of the dryer drum evenly and ensure that the different bumps a...
$73.05
In Stock
Door Switch Assembly
PartSelect #: PS4210737
Manufacturer #: DC64-00519B
This is a door switch assembly designed for Samsung washing machines. This door switch assembly is used to latch and lock the door shut before the washing cycle commences and communicates with the con...
$34.13
In Stock
Outer Seal Clamp
PartSelect #: PS4218211
Manufacturer #: DC97-04973B
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made o...
$17.35
In Stock
VALVE-WATER;V-0117,NYLON
PartSelect #: PS4209100
Manufacturer #: DC62-30314K
One solenoid valve for hot water
$89.85
In Stock
Water Temperature Thermistor
PartSelect #: PS4214274
Manufacturer #: DC90-10128N
The thermistor monitors and helps regulator the water temperature in the washer.
$87.25
In Stock
Washer Bolt Assembly
PartSelect #: PS4217876
Manufacturer #: DC97-02412A
Assembly BOLT;SWF-P12,MOTOR/
$13.62
In Stock
SEAL-TUB;GW-PJT,EPDM,H62
PartSelect #: PS4213806
Manufacturer #: DC69-00804A
This is a seal for various models of Samsung washing machines. This part acts as a seal for the rear and front outer part of your washing machine tub and is used to prevent any matter of leaks. If you...
$38.76
In Stock
Questions And Answers for WF219ANB/XAA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WF219ANB/XAA
[Viewing 3 of 3]Will not drain
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Code indicating washer was NOT discharging water
Watched the video, procedure was simple and as depicted on the video. Started by using a wet shop Vac to the discharge hose and sucked as much dirty wash water out as possible. Removed the pump,and found the motor did not turn freely. Removed the motor (3 screws) and replaced the motor with new part. Reassembled the washer, everything wor
... Read more
ked as it should. After about 3-4 loads of laundry, the "Not Draining" code / problem returned. Again, sucked out the water with the Shop Vac. Checked the Filter /Cleanout and found it completely packed with MUD. Cleaned that out, and again disassembled the washer. The pump was removed and the remaining muddy gunk was cleaned from the impeller. The 3 drain lines that attached to the pump were inspected for blockage/obstruction and flushed of any muddy residue. Reassembly was quick and easy, and the washer has worked well since. I have no idea how the dirt got into the system with enough dirt to gunk up the system. Recommend keeping more frequent inspections of the cleanout trap.
Read less
Parts Used:
-
SCOTT from VERNAL, UT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer making noise a snow smoking.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
Parts Used:
-
Samuel from NEEDVILLE, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
9 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front loader door would not lock.
Removed the rear top two Phillips screws, pull off top cover. Unscrew two phillips screws that hold the outside front lock trim, unclip (one left of housing) plastic housing. Remove one phillips screw 11 o'clock from housing, about 6" away, with door button above it, which releases the door lock housing from inside the machine. From right
... Read more
side (facing machine) look down into left front of machine, you will see a black cover, which does a goid job hiding the white part, but it protects the part from water, I guess. Unclip 3-4 plugs, push spinning loader away to pull out the complete part easily. Swap back covers (a bit annoying to place wiring harness back in such a tight place, and cover on. You can try another method if you have a simpler way, like place the harness onto part first, before plugging in and placing cover. But, I kept dropping the part into the machine, which equals a little pita). Then screw the 11pm screw to hold part and the two other screws (small housing and cover), place remaining 2 screws, and lid. Pretty much undo the above procedure. Done.
Read less
Parts Used:
-
Nadira from JACKSONVILLE, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!