Models > WEG745H0FS0 > Symptoms > Will Not Start

Parts That Fix Whirlpool Range WEG745H0FS0 Will Not Start

Will Not Start is a commonly reported symptom for the WEG745H0FS0 Whirlpool Range, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your WEG745H0FS0 Whirlpool Range that will fix Will Not Start. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

Fixes Symptom 64% of time
★★★★★
★★★★★
4 Reviews

Rated by 1 customer 

  

Really Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

Whirlpool Genuine OEM W11107275 Range Cooling Fan Motor. Possible Repair Solution For: Will not start, takes too long to cool Please Note: This is intended as a guideline only, as other items can cause the same symptoms. This part works with the following brands: Whirlpool, Roper, Admiral, Maytag, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric

$ 120.82
  In Stock
PartSelect Number PS12347171
Manufacturer Part Number W11107275

Customer Repair Stories

FE80 Error, blower motor underperforming

Remove cover under controls, unscrew rangetop (front only). Motor on right side of oven directly under rangetop detaches with 3 screws and remove with care. Swap foam seal to new motor and install. May require contact cement to attach seal to new part.
  • Richard from EUGENE, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 22% of time
★★★★★
★★★★★
7 Reviews

Rated by 2 customers 

  

Very Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

$ 87.01
  In Stock
PartSelect Number PS11752876
Manufacturer Part Number WPW10324262

Customer Repair Stories

Ignoter gave out

Opened oven... removed grates and bottom panel. Unbolted igniter has flange and end wire. Attached end wire to new igniter and reattached new igniter to gas flange. The rest in reverse and set oven and pressed start.
  • Michael from CHICAGO, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Faulty ignitor

Remove bottom plate take screws and hex head nuts remove wire unscrew ingnitor reverse process with new ignitor very easy
  • Mark from HOLLAND, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 8% of time

Rated by 5 customers 

  

A Bit Difficult 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

7-18 x 3/4-Inch - sold individually.

$ 6.53
  In Stock
PartSelect Number PS11741257
Manufacturer Part Number WP3368921
Fixes Symptom 7% of time
★★★★★
★★★★★
12 Reviews

Rated by 13 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

The light socket on your electric range connects the power source to the light bulb. If your oven light is malfunctioning, you may need to replace the light socket. The light socket is located in the back of your range, so in order to access it you will need to remove the back panel. Many of our customers have rated this repair as easy, and it should take less than 15 minutes. Before you begin this repair, make sure to disconnect the power source from your range. This is an OEM part sourced directly from the manufacturer.

$ 59.58
  In Stock
PartSelect Number PS16730838
Manufacturer Part Number W11594027

Replacing your Whirlpool Range SOCKT-LITE

Replacing your SOCKT-LITE

Customer Repair Stories

Inside brass liner in socket came out when bulb was removed. Apparently had welded itself to the base of the bulb

Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.
  • Lewis from Chapin, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
21 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Socket Light had a bad thread

Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover
  • Edmund from Emporium, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
44 of 61 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!