Switch to Classic
Models > WEF365BHWA > Instructions

WEF365BHWA Westinghouse Range - Instructions

All Instructions for the WEF365BHWA
16 - 30 of 725
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broke drawer glide
This was very simple I just snap the part on no tools required. it took less than 2 seconds.
Parts Used:
Front Drawer Glide
  • Tracy from Poulan, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
95 of 155 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned out burner
First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the different sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!
Parts Used:
Radiant Element with Limiter - 1200W
  • Lori from Winter Haven, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
56 of 67 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower element burned into.
First thing I did was to turn off the range supply breaker. There were two screws, one on each side, that held the lower element into place. I used a phillips head screw driver to remove the screws and pulled the element out for access to the wires. I pulled the connectors off of the element and remove it from the oven. I them put the new element into place, attached the wires, replaced the screws and turned on the breaker. It was an easy fix.
Parts Used:
Oven Bake Element
  • Richard from London, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
53 of 61 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven light receptacle broken - bulb base broke off
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
Parts Used:
Oven Light Socket
  • Paul from Spokane Valley, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
55 of 70 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch Was Making A Arcing Sound When Burner Was On
Removed the back cover of the range. Removed the knob from the front of the switch. Removed 2 screws holding switch to range. Removed wires one at a time and connected to proper poles on replacement switch and reinstalled new switch on range
Parts Used:
Infinite Burner Switch - Small Element - 240V
  • Gerald from Paris, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
55 of 77 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bake element burned out/ no oven heat.
I removed the two element screws, one on each side. This was very easy and fast.
I then pulled the old element towards me about
three inches to expose the wires attached to each
end. The wires have a slide on terminal connector
so replacement is easy, but you must hold the
terminal connected to the wire then pull the element off. Do not try to pull off the element by pulling on the wire you can cause damage to the
wire and create a new problem. Once the old element was removed I attached the wires to the new element by sliding the terminal connectors on each end and pushed them firmly into place. I then pushed the new element back and replaced the screws on each side and the repair was complete.The repair took all of about 5 min. The best part was I received the the new element from Parts Express the next day and had the oven working within 24 hrs.. The repair service could not do it that fast. Do it yourself, you can save a lot of money!!
Parts Used:
Oven Bake Element
  • Tom from Ridgefield, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
43 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Internal glass broke on the oven door
All the was needed was a Phillips screw driver. It's not difficult. Watch out because the door is spring loaded and does seperate quickly after all the screws are out. Be sure to watch the front panel, it appears to be heavy glass and can come out of the slots during the repair. I only had to re-assemble and dis-assemble 4 times before I got it right but it's still fairly easy to do if you take your time.
Parts Used:
Inner Oven Door Glass Panel
  • EDWARD from PHOENIX, AZ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
40 of 41 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drawer glide on bottom stove drawer broke
Snapped the new part into the slot the old one had been in.The repair including opening and closing the drawer took less than a minute.
Parts Used:
Front Drawer Glide
  • Homer from Thomaston, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
69 of 129 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
If burner was placed on HIGH, it wouldnt lower heat once LOW setting chosen
I had to replace the switch in the back of the control knobs. I was very grateful to the female phone attendant who answered my call. Since my part number had switched a few times, she took the time to reverify the "blueprints" of my machine with the parts carried at Parts Select and she helped me be assured that I was buying the correct part for my machine. She was SOOOO helpful. Will definately buy again from your store.
Parts Used:
Infinite Burner Switch
  • Juilo from Lake City, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
35 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
We notice a hot spot on the bake element while cooking and the next day the burner wouldn't heat.
First I unplugged the the stove. I then unscrewed the two screw holding the element. Because I had read the other repair reports on the site, I was very careful in pulling the element out so I wouldn't lose the wires in the rear of the stove.
Once out, I held them with the pliers and gently pulled the element until it was loose. Plugged in the new element screwed it back in and plugged in the oven. Worked like a charm. By the way the part arrived the day after ordering it!!!! This is a great site.
Parts Used:
Oven Bake Element
  • Nancy from Barrington, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
38 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
anti-tip bracket not installed
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.
Parts Used:
Anti-Tip Kit
  • Brian from Panama City Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
32 of 40 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rf burner was not working
First I removed 2 screws that held the stove top in place. Raised the stove top and support it. Then, I removed the hold down spring for the burner and removed three wires from the old burner. I found that the connector on the white wire was spread open too much so I crimped it closed for a better fit on the terminal. I reattached the three wires, put the hold down spring back in place, lowered the stove top and installed the 2 screws. JOB DONE
Parts Used:
ELEMENT
  • Neil from Jessup, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
34 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower baking element would not heat up.
Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim
Parts Used:
LENS Oven Bake Element
  • Jim from Harrison, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
36 of 55 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front Burner was on high all the time when on
Turn off the breaker to the stove. Very important because when you move the control panel around after removing it, you can inadvertently touch a hot wire to a grounded metal part on the stove. Remove the 3 nuts from the back of the control panel and the two nuts from under neath the control panel on either far side. Pull the control knob off by pulling straight away from the control panel. Remove the switch by unscrewing the two screws. Match the 5 wires from the old switch to the new switch by removing one at a time and paying attention to the labeling of each on both switches. Reassemble in reverse order. Turn breaker back on.
Parts Used:
Infinite Burner Switch
  • Gregory from Monument, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
28 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler element burned out
Remove old element by removing two screws on back wall of oven, pull attached wires out about 6" and disconnect. Reverse to install, very easy. Of course the oven door makes it harder to get at things, but it all worked out. Partselect was the only place I could find the element since the stove is 18 years old. I love keeping appliances going as long as possible.
Parts Used:
Broil Element
  • louis from cuba, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
26 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WEF365BHWA
16 - 30 of 725