WED6600VW0 Whirlpool Dryer - Instructions

actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)

After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.

My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.

super fast shipping, got the part in two days, and had it done in 15-20 min, remove the front pannel, remove the belt and tenssioner,took the drum out , took the old rollers , lubed the shafts,replaced the old rollers with the new ones, intalled the drum back, the tenssioner and the new belt, reinstalled the front pannel, and done...easy and fast job, like new dryer, works nice...save some money...the new one will do the same..just dry the clothes.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I wasn't sure if I was going to be able to do the repair myself. Happily, I was able to and my dryer works like new ! I figure I probably saved about a 100 bucks doing it myself rather than calling out a repair man. Oh, did I mention I am female and didn't have to have a man do this for me. :)

The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.

Pryed the top off the dryer, unplugged the door switch, took the screws out of the front panel, then lifted the drum out. Placed the new belt around the drum and while my wife held it in place and steadied it, I reached underneath and looped the belt through (as per instructions), reassembled and back in business! Reaching under the drum was not that easy....VERY tight space to work in and there was no way I could get both hands through, I almost gave up, but one last try and a couple of good grunts, and it popped into place. Getting the wires back on the door switch was a bit of an ordeal too. Took about 30 mins. but still worth it. I'm sure I saved at least a $100 repair.

I ordered up a new heating coil. It was plug and play, real easy to do. Make sure to turn on the dryer with the before you put it back together to make sure the heating coils heat up. Be careful though, it will get real hot, so run for a second or two. Also, you may see a little smoke as the coil burns in, that should be fine. Once it is tested and works, let it cool off, then reattach it, put on the backplate and you are done!

I removed the four screws holding the
heating element, then I pulled the element out
and then put the new element in and hucked
the wires from the old element after I disconnected
them to the new element..no problem......

1. UNPLUG 2.Undo 8 screws @ back of dryer. Locate heating element midway down on right about 6"x10" has three thermostat wires connected to it undo the 2 screws & 3 wires either order. You will need to pry up GENTLY on the thermostat on the old element. Replace themostat to new element and make a test run to make sure its running and HOTand repeat steps in reverse order...

Took the back off with a cordless drill with an apex holder. I unplugged the old wires from the old heating element and plugged them into the new heating element. Put the back back on after testing it to make sure it worked and that was it. Since this element was in a housing it was really simple to reinstall the new one.

It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum back in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone

took off about 8 screws, opened door into it's front & back parts, popped out the old/broken door catches and re-inserted replacements. Only 1 is needed, but this is the 2nd one to break. The first time a repairman switch the un-used from right side to left. (there are 2 so the door can be hung left or right opening)

Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!