Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WDSR4110T5WW

WDSR4110T5WW General Electric Washer - Overview

Get Parts and Repair Help for WDSR4110T5WW

If you know the washer repair part you need, you can browse the list of all parts on the WDSR4110T5WW, or you can search by name or part description. You can also find your part by where it is located on the WDSR4110T5WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WDSR4110T5WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.50

Tub Dampening Strap

The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noi...

Order within the next 6 hrs and your part ships today!
$4.69

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the timer will not advance, or the dryer shuts off too soon, the issue may be the control knob itself. This part is sold individually. Although this part fits with some different brands, be sure to check the list of brands below to make sure it fits with your dryer unit. Refer to the manual provided by the manufacturer for further installation instructions.

Order within the next 6 hrs and your part ships today!
$35.43

Agitator

This is a dual-action agitator for a washer. This is an OEM replacement part that is sourced from the genuine manufacturer. The agitator tosses your clothes to clean them efficient...

Order within the next 6 hrs and your part ships today!
$7.42

Agitator Coupling Kit

The agitator coupler connects the agitator to the agitator shaft. Common symptoms of a damaged coupler include: a grinding sound during the wash cycle, the washer refusing to agitate or spin, or the washing machine shakes and moves during the wash cycle. Unplug the washer and pull the agitator straight up. Remove the bolt that holds the coupler onto the shaft of the transmission and pull the coupler off. Be sure to clean any dirt, rust, or residue off the transmission spline grooves, and make sure the grooves on the agitator splines are clean and undamaged. We recommend using the gasket and bolt that come with the replacement coupling.

Order within the next 6 hrs and your part ships today!
$9.22

Selector Knob with Clip

This knob accepts a D-shaped shaft. Sold individually.

Order within the next 6 hrs and your part ships today!
$13.26

Drain Hose

The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drain. If this parts cracks or becomes damaged it will leak during the drain cycle of your wash and you may find water on the floor. To access the hose, you will need to move the washer away from the wall to get to the back of the appliance. There will be two screws holding it in place that will need to be removed.

Order within the next 6 hrs and your part ships today!
$3.62

Timer Knob Clip

The timer knob clip on your washing machine connects the timer knob to the control panel. If your timer knob is damaged or will not stay in place, you may need to replace the clip....

Order within the next 6 hrs and your part ships today!
$7.52

Tub Seal

The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at agitation time, your tub seal may need to be replaced. You can check if the tub seal needs to be replaced by watching that area during an actual fill cycle. Take off the front panel, or if it is a front-loading washer, the rear panel. Without touching the washing machine, observe the place where the shaft of the transmission comes into the tub and the weep holes at the housing of the rear bearing. If there is water leaking, the tub seal is at fault. NOTE: This seal is difficult to replace and should probably be installed by a qualified technician.

Order within the next 6 hrs and your part ships today!
$56.62

Drain Pump and Motor Assembly

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will...

Order within the next 6 hrs and your part ships today!
$3.42

Tub Bearing

This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a wash cycle. The most common reasons for needing to change your tub bearing is if your appliance is noisy or shaking/moving during the wash cycle, another common symptom is leaking water. This part is sold individually and measures to have an inner diameter of roughly 1 inch, and an outer diameter of roughly 2 inches.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

One of eight clips broke off of the agitator assy allowing the assembly to come lose on heavy loads.

  • Customer: Paul from Carneys Point, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 630 of 669 people found this instruction helpful
I replaced the coupling by only having to remove one bolt with a socket wrench. Once replaced I installed the new assy over the coupling making sure ro align the splines then pushing down until the assy snapped into place. Easy. read more

Replaced broken START knob on dryer.

  • Customer: SAM from ROCK HILL, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 488 of 496 people found this instruction helpful
Slid off the old START knob, then pushed on the new START knob.

I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.<... read more

The inside of the Selector Knob was stripped

  • Customer: Frank from Irvine, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 377 of 380 people found this instruction helpful
Removed the damaged knob and replaced it with the new knob. Very ease read more