Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WDB11NRDB3 > Instructions

WDB11NRDB3 Westinghouse Dishwasher - Instructions

All installation instructions for WDB11NRDB3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WDB11NRDB3
226-240 of 475
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Thanks for the help

  • Customer: Robert from Greenville, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
I removed the screws from the inside of the dishwasher door to allow access to the inside of the door. Once the exterior of the door is removed the detergent dispenser is easily removed by disconnecting 6 screws and unplugging two wires from the unit. The new unit slips in and is easily reconnected. Getting the exterior of the door reinstalled is a bit challenging, but once you figure out that the exterior needs to slide up to allow the catches on the door to grab, reinstallation is easy. A second pair of hands makes this easier.

The part fits exactly with no modifications necessary.

Soap dispenser door broke off

  • Customer: Sherry from Milton, VT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
First I unplugged the diswasher, than I unscrewed 4 screws on the inside of the door which pops the door off, unplug two wires, note which one goes where, unscrew 6 screws that holds dispenser in place, than reverse order to install new part. Very easy.

Broken spring on door

  • Customer: Donald from Marshalltown, IA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
Replaced spring on door

lower rack rollers were missing

  • Customer: Kathy from Greer, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Rollers just snapped on the diswasher rack. Took just seconds to do.

Main Soap dispenser lock is broken

  • Customer: Quan from Spingfield, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Unscrew all the scews arround it. Use tape to hold the eletronic panel. Remove the metal cover.
Remove the 6 screws around the dispenser. Replace the new one. Put the metal cover back first. Put back the electronic panel at last. Done

dishwasher leaked around the door

  • Customer: Clarence from Gerald, MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 2 people found this instruction helpful
My Son used needle nose pliers to remover the old gasket, then starting on the lower right side, inserted the new gasket and used the rounded end of handle of a wooden spoon and pressed the gaste in place by running the handle up and around the top then down the left side. Used sissors to cut the new gasket to length. Door fit very tight. Ran a normal wash cycle and no leaks.

would leak front left corner

  • Customer: Jacob from nappanee, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 2 people found this instruction helpful
took out screws around door, took off hinges, slip new seal in put hinges back on screws around door. does not leak

Soap dispenser door wouldn't open fully - spring broken

  • Customer: stewart from holliston, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
I did not come with directions, but I had gotten them from the Parts Select stories from others. Removed 2 screws from inside door, dropped the front panel, removed the 6 screws holding the dispenser, unplugged the contacts, removed the dispenser and then reversed the process.

Latch On The Dispenser Was Broken

  • Customer: Michael from Alpine, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
Remove the inner door panel, plastic, has 8 screws, unplug the dispenser compartment, and do the reverse. This was very easy. Thanks partselect!!!!!!!

No water during wash cycle, steam only

  • Customer: ANDREW from APPLETON, WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 1 of 6 people found this instruction helpful
After checking various forums and advice, the suggested repair was a new water inlet valve. It was easy to change but I wasted $30 as it did not cure the problem. Dishwasher is only 2 years old and is cheaper to replace then have someone come and look at it. So it did not fix the problem, but I recommend Parts Select, the price was fair and part arrived very quickly.

Leak at bottom of door

  • Customer: Ronald from Soperton, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Removed door gasket then replaced bottom gasket

dishwasher leaked by bottom of door

  • Customer: Mark from Raleigh, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 4 people found this instruction helpful
Removed door covering. Removed door (it was nice to have a helper for this as the hinges spring closed as the screws are removed). Flipped door over, leaving the wires attached. Removed the bottom seal, and put new one in. This looked like it would slide out by a side, but it actually pulls straight down. It is notched, so there isn't a way to put new one in the wrong way. Attached door (again helper a bonus). Attached door cover.

was brocken

  • Customer: Aleksandr from West Palm Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 31 people found this instruction helpful
just replace

door leak

  • Customer: Andrew from Republic, PA
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out old gasket and replaced with a new one.New gasket snapped right in place in bottom of door,

the botton door gasket was not very easy to install

  • Customer: Col USMC ret Joseph from Anchorage, AK
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This not was very easy to install I have to remove the fron panel of the dishwasher to see were to insert the new gasket i you instruction how to instal this was insert the new gasket from the rigth side to the left well if you look the front of the diswasher you insert from the lefth in to the place how hold the gasket inplase was not very esy to install but was don and working OK.
All Instructions for the WDB11NRDB3
226-240 of 475