WD-3245RHD LG - Instructions

Honestly youtube but pretty simple install.

I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.

Watch the video to repair and follow along

followed instructions on video , when part was delivered I had washer fixed in about 1/2 hour, very easy to fix . Wife is happy and I saved a lot of money. Thank you partselect.com

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.

Follow the LG washer video.

Not too bad, had a neighbor help with the project as washer/dryer were stacked. removed dryer from on top out of way. Drained washer, tilted on side to get access from down below. Second person help here. unscrewed drain pump from front, Used pliers to unclamp hoses, disconnect wires to motor (already pulled power from wall) pushed plastic clip holding in unit and pulled out. New unit was factory new, not a knockoff. We took extra time to clean out hoses, especially from the main washer unit, it was a simple unscrew clamp and pull hose down. We sprayed out gunk from hoses and parts going back in. Once new unit was ready, installed back and reconnected hose and power. The clamps were somewhat of a pain with the overall size and angles to get them seated and on correctly. Much easier to take off, but take the time to reinstall correctly. Don’t need water leaking. Motor much quieter now, wife is happy.

you tube it , not to hard to install

Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!

After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went so I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.

Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires

I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars

Remove where the water pumps are and remove the one that was damaged easily

When to utube typed in my problem, very easy fix

I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.