Models
>
WBB24751FF
WBB24751FF ((03)) Bosch Washer - Overview
Sections of the WBB24751FF
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Door Hinge
PartSelect #: PS8731238
Manufacturer #: 00651004
The hinge is mounted on the front of the washer, and the door is installed onto the hinge. When the hinge on a washing machine is broken or bent the door may not swing properly, and it may not close. ...
$38.38
In Stock
Bellow Assembly
PartSelect #: PS8732873
Manufacturer #: 00667489
This is a bellow assembly, also known as a door boot gasket kit, and it is designed for use with front load washers. This gasket acts as the main seal between the door of the washing machine and the w...
$83.15
In Stock
Shipping Bolt with Spacer
PartSelect #: PS8697774
Manufacturer #: 00175724
Front-loading washing machines use a suspension system to support the tub during the wash cycle. This suspension system is only designed to handle a certain amount of movement, so when you are transpo...
$18.12
In Stock
Washer Drive Belt
PartSelect #: PS8722578
Manufacturer #: 00491680
This drive belt is for washers. Drive belt connects the drive motor to the drive system in the washer to spin the basket.
No Longer Available
Shock Absorber
PartSelect #: PS8729758
Manufacturer #: 00642112
Shock absorbers keep the washer from vigorous shaking during it's cycles. They are sold individually.
$61.53
In Stock
Questions And Answers for WBB24751FF
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WBB24751FF
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Hinge bracket snapped off
Removed washing machine door. Then removed old hinge. Replaced with the new hinge. Replaced door. SPECIAL NOTE: Do not lose white plastic rings that cover hinge nipples on washer. The replacement part does not come with these 4 pieces.
Parts Used:
-
James from ALEXANDRIA, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
14 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The sleeves on this model washer are two different sizes see below
The thickness of the sleeves are 3.0 mm thick on the base of the sleeve. However the sleeve on the bottom of both the upper and lower hinges of this model washer are different sizes. The base of the sleeve on the top of each hinge post is 3.0 mm but the sleeve on the bottom post of each hinge is only 1.2 mm thick. The bracket on the d
... Read more
oor that holds all 4 screws to attach the door to the washer will not fit unless you reuse the old sleeve from the lower posts or reduce the thickness of the disc on the lower post to 1.2 mm. I spent hours trying to get the door back on and finally saw why I couldn't get the screws back in because the bracket could not go in place and sit flush the the washer.
Read less
Parts Used:
-
David from ENTERPRISE, AL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Repurposing Washer to a rental, seal was smelly and uncleanable.
I watched the great video on youtube first, my washer model was a bit different, and removing the front panel was a bit different, but easy to figure out. I also had to remove the door separately. In order to install the first clip spring, I had to loosen the counterbalances a bit to get the seal properly aligned. From there I was able
... Read more
to install the spring clip my myself. So far, so good, installing the second clip to the front panel was quite difficult by myself, and the rubber kept popping out of the gap. Finally I enlisted another pair of hands to hold the clip in place up top and on the sides while I stretched the spring around the bottom. It took about 5 tries before we got it secured.
Read less
Parts Used:
-
Barry from EL DORADO HLS, CA
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Socket set
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!