Models
>
WA3900AWL2
WA3900AWL2 Frigidaire Washer - Overview
Sections of the WA3900AWL2
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Drive V-Belt
PartSelect #: PS1146950
Manufacturer #: 134511600
This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does no...
$24.93
In Stock
Water Inlet Valve
PartSelect #: PS815509
Manufacturer #: 134190200
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
$127.65
In Stock
Screw-In Plastic Leveling Leg
PartSelect #: PS1152204
Manufacturer #: 134548800
This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your a...
$25.94
In Stock
Tub Seal Assembly
PartSelect #: PS459481
Manufacturer #: 5303279394
If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make ...
$74.78
In Stock
Tension Idler Pulley
PartSelect #: PS418897
Manufacturer #: 131862900
The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operatin...
No Longer Available
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$11.21
In Stock
Washer Lid Lock with External Safety Switch
PartSelect #: PS648775
Manufacturer #: 134101800
Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).
No Longer Available
Agitator
PartSelect #: PS446533
Manufacturer #: 3204401
This is an agitator that is compatible within various makes and models of washer, and is used to move, or agitate, the clothes and soap/water mixture around within the tub of the washer. This agitator...
$101.04
In Stock
Agitator Drive Block
PartSelect #: PS1152574
Manufacturer #: 134418700
The agitator drive block rotates the agitator assembly in your washer. If the drive block breaks down due to wear and tear the agitator will stop working. If you notice that your washer is making loud...
$63.38
In Stock
Spin Bearing
PartSelect #: PS446536
Manufacturer #: 3204405
The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, therefore ensuring the sha...
$77.44
In Stock
Upper Spin Bearing Washer
PartSelect #: PS473382
Manufacturer #: 5308002401
The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are ...
$12.94
In Stock
Tension Spring
PartSelect #: PS446551
Manufacturer #: 3204425
This tension spring works in conjunction with the idler pulley. The spring is part of your top load washing machine assembly. The most likely reasons for needing to replace the tension spring is if yo...
No Longer Available
Questions And Answers for WA3900AWL2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WA3900AWL2
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace broken drive belt
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub p
... Read more
ulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Read less
Parts Used:
-
rodney from fairfield bay, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
276 of 308 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and remo
... Read more
ved the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read less
Parts Used:
-
alvaro from east hampton, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
86 of 96 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid Lock Assembly broke
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would
... Read more
need to pay a repair person to do!
Read less
Parts Used:
-
Jenessa from Tacoma, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
74 of 92 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!