VVSR1070D5WW Hotpoint Washer - Instructions

First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.

removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

turned off the water and removed the hoses. Then removed the screws that held the back plate (that contains the knobs). removed the two screws holding the water valves and the hose to the washer. replaced the valve and then reassembled the rest.

Removed knobs, removed cold and hot inlet hoses,removed top cover, removed output hose, wire plugs, and three screws and replaced the valve.

the repair was really easy. All I did take down the control panel, disconnect the wires, pop out the switch, and blow through the air hose. I didn't realize what a simple machine it was.

turned washer on side to get at the bolts holding motor. loosen bolts. remove flexable basket for water pump or one end of it. slide motor to loosen belt. remove and replace belt. use large screwdriver on motor to hold tension on belt while tightening nuts. hardest part was getting clamps back on the rubber basket.

I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

Took complete tub assembly out of washer and inspected it. Did not find an obvious cause of leak but all 8 screws on inner tub hub were loose. As both tub nut and split ring were corroded, replaced them and the outer tub seal. Did a lot of cleaning!! As I was putting the trans assy back on the outer tub, I noticed a crack around the drain spout. At 1st, it looked like it belonged there but a closer look proved it didn't. I ordered a new outer tub (which came in 2 days) and I put the whole thing back together. Reassembly was far easier than disassembly was and I learned a whole lot about washers. YouTube is a great source of information.

I had no difficulty dismantling the washer until I got to the hub nut. It was frozen to the cone shaped fitting it was resting in. I had to take a drill and a 3/16" drill bit and drill the flange of the hub nut and then take a chisel and break it off piece by piece. Once that was off, I lifted the tub out and tried to pry off the split ring under the tub and it too was corroded and broke when I tried to pull it off. So I would advise you to buy a hub nut and a split ring if you are replacing the tub bearing, just to be safe. I went to an appliance parts store here in town and bought them. When reassembling the tub, I couldn't get a wrench or pliers on the hub nut to get enough torque to tighten it securely. And since I didn't want to spend $43 to buy a spanner wrench for a one time repair, I went to Harbor Freight and bought a $15 dollar adjustable wrench and cut 3 1/2" off the handle so it would lay flat to the tub and used a hammer to tap on the handle to tighten it securely. If you do not find some way to tighten the tub securely, it will come loose in the spin cycle like it did on me twice before I purchased the adjustable wrench and modified it to work. Plus I still have a useable adjustable wrench. Additionally, I took the washer cabinet, the tub and the tub sleeve and power washed it to get years of grime off of it. The washer now operates like new, saving me hundreds of dollars.

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.

unplug machine and turn off water at the valve. the pressure switch is located behind the water level control knob. remove the knobs from the panel, then remove the panel on the top back of the machine and remove the wires from the pressure switch. unplug switch. attach wires to new switch and plug into place. replace panel and replace all the knobs.turn on the water valve and plug into outlet.