Quick Question!

Have you ever purchased from PartSelect.com before?

Models > VBSR2080W0WW > Instructions

VBSR2080W0WW Hotpoint Washer - Instructions

All installation instructions for VBSR2080W0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the VBSR2080W0WW
391-405 of 594
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

After a wash cycle, water kept dripping into the tub

  • Customer: James from Simi Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
After figuring out to use a very small flathead screwdriver to get out the "star" screws holding on the front panel, since I don't have the proper tool for this, it was easy! Just disconnected hose lines from back of washer, unplugged the old valve, removed the screws holding it in. I disconnected the small water line that was connected to valve. I put in the new valve, reconnected everything, put panels back on, and it worked like new again.

tub wouldn't drain

  • Customer: daniel from walkersville, MD
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Easiest thing I ever did on the computer. U tube helped me diagnose the problem and how to remove the old pump and install the new. Parts Select menu was easy to navigate and had a picture of the pump I needed. The cost was affordable and I got the satisfaction of making the repair myself.

Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor

  • Customer: Arlis from Moore, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.

Cold water was dripper after each washing cycle.

  • Customer: Roque from Brentwood, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1)Remove the 5 screws from the back panel to gain access to the dual inlet valve. 2)Disconnect the wire from the valve. Then, remove the screws the hold the valve. Then, remove the C-clamp from the valve to get it loose. 3) Then, reverse the procedures to install the new valve.

replaced leaky tubseal

  • Customer: Michael from Hollywood, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Repair went great. The large nut had to be soaked to free it but the part was an exact fit.

Pump was broken

  • Customer: Dawn from Singers Glen, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
So easy to fix. The best thing about it all was the guidance of the website. We were able to locate the exact part and followed the instructions on how to replace, piece of cake!

Washer was overflowing both wash/rinse cycles

  • Customer: Dennis from Charlotte, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ok it was easier than typing this email. Remove selector knob. Use star*screwdriver to remove 4 screws at top. Pull the panel out toward you, lay down.Pry the lock tab up slightly with knife/flathead to clear the groove twist switch half turn counterclockwise and remove. Pull the vacuum hose off. Remove 2 wires. Now do it again in exact same order only in reverse. Youre done. Saved aprox. $280.00 and was a hero for the rest of the day.

Washer was not running

  • Customer: Susan from Old Orchard Beach, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Found out the screw was stripped from the agitator, probably because the washer is over 10 yrs old. We got the right part! The parts store was very fast in shipping, in fact we got it the next day! Highly recommend PartSelect!!!!!!!!!!

Agitator not moving

  • Customer: Erik from Raleigh, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed fabric softener cover by pulling up. Then removed agitator by grabbing at the bottom and pulling up. Note I did read online that some may have a bolt holding the agitator down thats what it seemed like when I read it. Mine did not have a bolt. after removing the agitator there is a 10 or an 11mm bolt holding it down remove that and the coupler comes right out then install in reverse order. All done. Also its a ge adora washer.

water would sometimes overflow on floor

  • Customer: Waldemar from Poway, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced dual inlet valve. Problem solved

The existing drain hose was missing and the clip was broken.

  • Customer: Tammy from Boone, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Inserted the drain hose and attached the clip. First test of repair leaked. Then I "fully" inserted the hose and fixed the leak.

3 of the 4 dampening straps were broken.

  • Customer: Walter from woodland, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.

water leaking from bottom of washer

  • Customer: jeffrey from willard, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

lid switch actuatof

  • Customer: Krista from Rock Hill, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pop out pop in, just that simple.

cold water would not stop running

  • Customer: Kelvin from Richland Hills, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Took out the old part and easily replaced it with the new part.
All Instructions for the VBSR2080W0WW
391-405 of 594