UMV2186AAS16 Maytag Microwave - Instructions

Why a tenant would remove and discard the grease filters without replacing them is beyond me! But, I removed the filters from the package and slid them into place. Two minutes tops. I would like to add that I ordered these on Thursday afternoon, and I had them on Saturday; awesome customer service!

The repair was very easy, however the bulb was not the same as the original one. The original bulb had a bright setting and a low setting, but the replacement bulb was only the low setting bulb. There was no bright and dim operation. The switch on the microwave had the duel settings.

Removed control panel, discharged HV capacitor. Removed old diode, tested to confirm failure. Replaced part. Other than the removal of the panel swapping the part was almost as easy as replacing a light bulb.

The high voltage tired was shorted. I replaced it with a new one, but that did not solve the problem.

You can test the high voltage tired with a voltmeter and a 9 V battery. Search Search for it on YouTube.

You can also test the high voltage capacitor, the high-voltage transformer, and the magnetron with a multi meter. Search for the procedures on YouTube.

I tested all these high-voltage components with a low-voltage multi meter, and they all checked out OK (after replacing the diode). However the microwave still did not heat food.

When working on a microwave it is important to unplug it and also discharge the high voltage capacitor. The capacitor has a 10 megaohm resister to automatically discharge itself, but it may have failed – – so discharge it manually.

In the end I ordered a new microwave.

With microwave still attached under the cabinets, I removed 2 screws for the top grill and then one screw for the bulb cover plate. This provided access to the bulb. The replacement bulb was a simple plug-in.

The best part of this experience was the exploded parts diagram on the PartsSelect web site which allowed me to easily locate and order the correct part.

Opened light panel and replaced bulb. Very, very easy.

I am concerned, however, that this bulb does not emit the same amount of light as the one i replaced. The item number is the same, however, so I am perplexed at this bulb efficiency.

Unplugged Microwave, Removed vent cover (2 screws on top of microwave, then slide cover to the left, then forward) Removed control panel (1 screw at top of panel) then removed the two screws that hold in the door switch assembly. (these you will only see by opening the microwave). Located lower door switch, removed connecting wires, and pulled switch by releasing small plastic tab which held it in. Put new switch in place, reconnected wires, then reconnected door switch assembly. Reconnected control panel, and then put the vent cover back on. Tested microwave and it no longer runs when the door is open. Super easy fix, and was done in under 5 minutes.

I followed the instructions in the owners' manual on how to access the bulb. Installation was a breeze. I couldn't believe how fast I received the replacement bulb from PartSelect. I ordered it on line one afternoon and Fedex delivered it to my front door before 9:00 A.M. the next day. Awesome service.

I removed the outer cover and exposed the inner workings. I watched a video on partselect.com to show how to remove and replace the Diode. I followed the instructions and it was very easy to replace.

Unfortunately, the diode was only part of the issue. I ended up replacing the High Voltage capacitor and Magnetron also. Those were a little more complicated but still easy to do.

Now the Microwave works just like new! Cost me less than $100 for all parts.

Removed the turntable and changed the coupler. Replaced the turntable.

Pulled out the old and inserted the new/replacement.

Replaced with new motor from Parts Select. Part was a correct replacement for the old one. perfect fit. Works like it did when it was new. I will recommend Parts Select to anyone. Thank you very much. I would definitely use your company again in the future. I saved $30 by not using parts from GE.

replaced the drive motor and coupler coupler from samsung parts

Replaced the bulb

To replace the light bulb was fast and easy. All I had to do was unscrew one screw and place the bulb in! Quick and easy, and simple!