Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TEF351EWC > Instructions

TEF351EWC Tappan Range - Instructions

All installation instructions for TEF351EWC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF351EWC
481-495 of 763
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

computer touch pad shorted out

  • Customer: Jody from Statesville, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced computer part and fixed better then buying a 400.00 stove that a I don't have right now need to cook and eat

Lens cover for oven light broke.

  • Customer: Amy from Corona, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Replaced heating element

  • Customer: Sheila from Monticello, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I went to video and followed instructions. I removed the holding brace securing the element in and pulled out old heating wire and installed new one that came a day after I ordered it. It was so easy and saved me over $100

bad burner switch

  • Customer: ALBERT from LITCHFIELD, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

So easy!

  • Customer: Patricia from Newburgh, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off the shipping was lightning speed and the repair was super easy anyone can do it.

Old element broke

  • Customer: Deborah from Varna, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
All I did unscrew bolts pull out element wires detach them attach new element to the wires push them back inside the openings reattach bolts all done easypeasy and I am a 63 yr old woman

Bad element

  • Customer: Darlene from Allons, TN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screws,pulled off clips,reinstalled new element.

heating element out

  • Customer: Elsie from Commerce City, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took to screw out pull to wire's out push to wire's back on put the screw back on complete less than 5minutes

Bake Element in Oven

  • Customer: Timothy from Titusville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Quite easy and takes 5 minutes Remove racks from oven. Use a phillips screwdriver and remove 1 screw from each side of baking element. Gently pull baking element slowly or carefully so you do not damage wires, insulation around wires or so they don't come off element before you can reach them. With a pliers, hold the metal clip attached to wire and pull off of baking element. Make sure wire will not go back into back of stove. Pull off opposite side wire in same manner. Take new element, check the orientation of the element, make sure it it going in correct, and slide wire clip onto one end of element. Do the same thing with the other wire on opposite side. Carefully feed wire back into openings in oven while placing element back in oven.. Replace screws on each side of element to hold in place. Turn oven on so make sure it element is heating. I left my oven on 400 degrees to burn off anything that may have been on the new element during manufacturing so it would not leave or transfer an odor to food when using the next time.

oven element not working

  • Customer: Patricia from Hendersonville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old element and just popped in the new one

Heating element , not heating

  • Customer: Joseph from Littleton, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1. Made sure replacement part matched the defective part. 2. Got the recommended tools. 3. Pulled out range away from wall. Unplugged range. 4. Opened oven door and removed two screws ( with nut driver ) that hold heating element and detached the two wires from the element with pliers. Threw away old element and than connected the two wires ( one to each end of the new heating element ) . Than I use the nut driver to secure the new element with the two screws I removed earlier. Plugged range back in and pushed it back against the wall. Than turned on oven and the oven heated very well. Less than 15 minutes to complete the task.

Bake element needed replacement

  • Customer: Paula from Cazenovia, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Piece of cake mostly because the video was very helpful clear and thorough

Oven bake element burned out

  • Customer: Charles from Saint Augustine, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced element

The lower oven heat element went out

  • Customer: Jim from Webster, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I went on line and looked up our Model no and serial number of our Frigidaire Range, on Part Select's website, found the part and ordered. Within 3 days the part arrived, and to work on the lower heat element, the two oven racks are removed then I used a small socket set to take the connecting screws out, pull the bake element out of the socket, remove the power cords, then reverse the process install the power cords(just easy slip on) and then reattach the screw, tighten, and put the two over racks back in their place. Turn the oven on and the oven worked beautifully.

aluminum foil melted on oven bottom

  • Customer: Allen from wakefield, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It cannot be cleaned as it welded itself to oven bottom. Two screws in back of oven bottom and it lifted right out. The new bottom says "do not use aluminum foil" Very easy repair.
All Instructions for the TEF351EWC
481-495 of 763