Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TEF326FBB > Instructions

TEF326FBB Tappan Range - Instructions

All installation instructions for TEF326FBB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF326FBB
481-495 of 924
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven was not heating up sufficiently, we determined it was the lower element.

  • Customer: Greg from Sedro Woolley, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
We turned off the power then unscrewed the element . After removing the element from the connectors we taped the wires to the oven so as not to lose them back into the holes. We attached the new element, pushed the ends into the holes and refastened the nuts. Very easy and now we are back in business.

two rear glides and one front glide had broken.

  • Customer: David from Claremont, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the short video on the site that showed how to replace the glides. It was key since it showed how to use a screwdriver to remover the old slide. The new ones then popped right in place.

Front drawer guides broke

  • Customer: Michael from El Paso, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Popped out the old...snapped in the new. All of about 5 minutes or less.

The drawer glide snapped in half

  • Customer: Alberta from East Glenville, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the replacement glide, received pretty quickly! : ) Snapped the broken part out with screw driver and popped the replacement glide in with my thumb! 1,2,3.... Pretty Happy!

Broken rear Guide

  • Customer: George from North Port, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced the guides by following the instructions in the Video provided on the part information page. Really simple.

Burnt out Bake Element

  • Customer: Donald from Punta Gorda, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video on your web site, and it couldn't have been any easier. This is the second major appliance that I've repaired using this web site, and your instructions have been perfect each time, as well as parts cost. I can't get parts at any lower cost including shipping! Excellent resourse here!!!

Oven bake element died

  • Customer: Dawn from Warren, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
repaired in 5 minutes with my nut driver. So, so, so easy to make this repair. And never even attempted to call an electrician. Since long before I became an official widow, I say...who needs a man...

Broken Drawer Slide

  • Customer: Richard from Woodruff, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the repair tutorial and followed the instructions. The order went very well and the tutorial was spot-on. Nice.

Bake element stopped working after 17 years

  • Customer: Michael from Lockport, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed the two screws which held element in place...pulled straight out...gently pulled connector terminals off....replaced with new element connecting element terminals ...sliding element back into place (make sure terminal connection is straight (ie NOT BENT) when pushing element back into original position)and screwing screws back in...DONE!!! EASY PEASY!!!

bake element burnt into

  • Customer: JEFFREY from HIGHPOINT, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed the screw at the mount on each side of element .pulled old element straight out untill wire connector was out at the back of oven ..unplugged wire connector from each end of old element ..plugged wire connectors back into new element .pushed element plugs back into back of oven and installed each screw that holds element into place.. real simple

Large burner switch made popping and buzzing noises.

  • Customer: Glenda from Miles City, MT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

the bakely element was burned into in two different places

  • Customer: jannetta from clarkton, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
aftering watching your repair video the repair went very well we took the oven door off to make access easier. the worst part of the repair was getting the door back on.

Oven would not heat to temperature

  • Customer: Robert from Lorena, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Undo the two nut screws pulled out the element and replaced it with the new one.

Element burned out; needed replacement

  • Customer: Michael from Spicer, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed instructions on YouTube and Frgidaire website. It looked easy; was easier than it looked -)

Bottom oven element no longer working.

  • Customer: Frances from Garner, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old element by taking out two screws at bottom rear of oven. Pulled element and wires forward from two holes and unclipped from wires. Clipped new element to wires and pushed the wires back into the holes. Then replaced the two screws. Needed flashlight so that 60+ eyes could see the screws and holes in the oven. A quick and inexpensive repair. Element was delivered very quickly.
All Instructions for the TEF326FBB
481-495 of 924