TDG336RBD1 Tappan Dryer - Instructions

Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.

Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

I remove the drum, and install the bearing just like the instructions in the video.

After removing the old drum glide there was tufts of felt and glue left behind. The DIY video (which inspired me to try this repair myself) says to use a scraper and wire brush to clean the drum edge. I decided to try a drill with a wire wheel. Worked great. The surface was shining clean in minutes.

pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

i followed the video step by step & i never thought a repair could go so well thanks to the repair video

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

After figuring out how to remove the top, front, and control panel from the Gallery series, which is different than the dryer in the video, the repair was easy. Just followed the rest of the proceedure in the video.

The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.

Replaced the front and rear drum bearings and changed the belt because the dryer was about 8 years old. The repair was easier than I anticipated thanks to the excellent repair video furnished by Parts Select. FedEx delivered the new parts within two days. Dryer works like new!

Followed video that was provided!! Now I know how to get the top and front of dryer OPEN. Now I can clean interior of dryer ALSO, lots of lent!!

I followed the instructions in the videos that came with the email I got when the parts shipped. I would recommend looking at all the parts that come with the kit before you start. The video says to reuse some parts, but you have new ones. Also, after unplugging the dryer, I used a flat screw driver to pop the tabs on the 'lid' of the dryer. Removing the two screws that hold the front on was easy, and removing the front to sit aside. The flashlight is nice when you reach under the drum to get the belt off the idler pully and motor pulley. Wiggling the drum out was a little tricky but not hard. After removing the drum, I vacuumed the lint and really cleaned the inside of the dryer. Taking the screws out of the inside of the drum would be easier if you can put it up on a table or other work surface. Bottom line, I'm a girl with arthritis and did it by myself, you can too :) Dryer runs like a dream

I want to suggest that you also purchase the lower drum seal or guide as well. When I took it apart I realized I needed it also.

I followed the instructions in a Youtube video that an individual made with his kids. The only hard part was removing the drum assembly, the rear drum bearing was very difficult to unseat. I had to reattach the front of the dryer to give the drum assembly more support to be able to lift the rear - but overall it was quite easy to figure out disassembly and reassembly of the dryer. There's really not that much to them.