Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TDE546RED0 > Instructions

TDE546RED0 Tappan Dryer - Instructions

All installation instructions for TDE546RED0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TDE546RED0
316-330 of 491
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer Heater Not Working

  • Customer: Daniel from North Port, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I never respond to any of these surveys, but in this case ill make an exception because they made it so easy and parts were received correctly a quickly. Thanks, dan

Loud Squeaking

  • Customer: Rene from Bell Gardens, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Very simple. Pop the top open released the beld from the back it's easier that way the video was very helpful the sound was so bad you can hear it from a few houses down after year of just using it like that I figured I ha d nothing to loose great price great instructions now it sounds just as new.

Loud squealing sound

  • Customer: Curt from Elkhart, IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructional videos for installing the rear drum bearing kit and the upper drum glide. The repair probably would have taken less than an hour, but extra time was needed to thoroughly clean out all the lint and dirt inside the dryer. Also, the spring that holds the belt idler in position came off and I didn't realize I had put it back on backwards until after everything was reassembled. When I tested the dryer I could hear the belt rubbing on the spring.

Lint filter was broken

  • Customer: BeLinda from Indianapolis, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I did was insert the new one! Service was excellent. I received it in one day!!!

noisy

  • Customer: Terry from Viera, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
after watching the video,I followed its instructions. No surprises No problems

Clothes were getting trapped at edge of drum and were being burned.

  • Customer: David from Pittsboro, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled dryer forward for access. Raised top by pressing clips on front. Removed front panel 2 screws. Removed old felt flange with plastic guides. Cleaned surface of old glue. Dried. apply cement per instructions applied new felt. New fit was snug and required some manipulation. When in place it helped to hold felt until cured. works great. Would not have known what problem was without the videos @ Part Select. Thanx for info and part. David

Dryer was make a really bad squealing noise

  • Customer: Ken from Pinole, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Saw video on YouTube on how to change rear bearing. Followed what I saw and repairs were made with ease. our repair kit included all the parts (new bearing) and everything fit perfect.

The belt broke on a squeaky dryer

  • Customer: christopher van from Milford, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I raised the top up by releasing the two clips in the front edge with a small flat head screwdriver. I used a bungie cord to keep the lid from bending to far back. I removed the front of the dryer softly letting the drum rest on the insides. I carefully removed the drum by pulling upward to disengage the rear bearing and not damage the heating element. I then cleaned the entire inside of the dryer with a vacuum, brush, and some compressed air. I then replaced and greased the new plastic bearing cup, installed the drum, slipped the belt on, installed the front cover, and hooked up the belt through the access door on the rear of the dryer. Checked to see if the system looked ok and closed the lid. Worked great. I would order a front seal felt kit also if I was to do it again.

Bearing And New Belt

  • Customer: steve from mountain home, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched the video on how to do the repair. Very good instuctions made the repair go smoothly.

Door would not close because of broken female latch.

  • Customer: Raymond Frattone from Richboro, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.

Loud squeaking noise

  • Customer: David from WASHINGTON, DC
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video. Very helpful. There is no way I could have done this on my own without that guidance. Parts in Rear Drum Bearing Kit included new screws and metal support parts that are shown as reused in the video. To install these parts, I had to hold the back plate in place. A big piece of masking tape did the job nicely. The only major problem was tapping the holes in part that attaches to the drum -- very difficult. Needed my best Phillips screwdriver, leather gloves, and a lot of hand strength to get it done. I had to slightly ream out one of the holes to make the last screw fit. Minor problem - the idler arm is not retained by anything. The idler pulley and arm both fell off when I reinstalled the belt. I guessed right on how to get them back on the machine.

loud squeek

  • Customer: Cheryl from Weirton, WV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed the Video instruction which were provided. Dryer works like brand new.

Left dark marks / streaks on clothes

  • Customer: Teresa from North Haven, CT
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just followed the videos. Figured as long as I was in there I might as well replace the belt, bearing and heating element. Hopefully I'll get another 10 years.

Loud Squeaking noise

  • Customer: David from Sioux Falls, SD
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Just followed step by step instructions from the video provided by Parts Select

replace rear bearing

  • Customer: Dwight from Milaca, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
This was a stacked washer and dryer combo and is a lot more difficult to repair, requiring a lot more to take apart and put back together.
All Instructions for the TDE546RED0
316-330 of 491