TDB647RHB0 Tappan Dishwasher - Instructions

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

New one snaps into place easily.

First I disconnected the dishwasher, then I disconnected the drain hose. I pulled the machine from under the counter and turned it on its side, so that I could see where the drain pump was. I removed the two screws that hold the element in place. I then pulled the pump out and disconnected the two wires. I took a good look where each wire was attached. I also had to disconnect the pump from two small hoses. I installed the new pump, I had ordered from PartSelect, following the reverse procedure. I reconnected the dishwasher and slided back under the counter. I confess I didn't believe it would work. I was prepared for failure. The machine started, then when the cycle changed, I heard the water draining into the waist pipe under the sink. New hot water filled the machine. Would this water be drained out and at the end, after the rinsing cycle, would the dishwasher be empty and completely free of water? I waited for the end of the rinsing, then I opened the door and checked for any water left at the bottom. Suddenly a feeling of joy and pride went through me. All water had been drained out by the new pump. I had repaired my dishwasher. I didn't have to throw this handsome and well made machine into the street. My kitchen sink was no longer full of glasses and dishes. I was washing all I had accumulated during the week. My kitchen became clean and organized just like before. At this point I took an oath: when my dishwasher would break down next time, I would repair it , even if its motor, the most expensive part, had to be replaced. I was going to do it with the help of the experts at PartSelect. Thanks guys for your help and for inspiring confidence in myself. I DID IT! What a great feeling!
Now I understand the feeling a doctor must experience when he brings back to life a dying patient.

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks

Removed 6 screws, pulled the front cover forward, removed the old door latch, installed the new latch, replaced the screws, DONE! Took about 10 minutes. The new door latch works to open and close the door, and the dishwasher runs fine when the door is closed. However, the new door latch does not lock the door into place like the old one did. I didn't remove the screws and loor latch assembly again, but there must be a difference between the old part or the new part. And I noticed that the old part number and the part number of the replacement part are not the same, although the website indicated that it was the correct part for my model.

Our dishwasher sat in a warehouse for a year after our move from CA to TX. When I finally installed it, there was some sort of white mineral deposit that had built up on the heater element. I didn't notice it back in CA. I tried to get as much as possible off but it kept building. So I purchased a new heater element. It's been in for a few weeks and my wife thinks the build up is happening again.
To Repair;
Unscrew the dishwasher from the counter. They'll be one or two screws attaching the dishwasher on the underside of the counter.
Pull the washer out carefully.
Remove any dishes and the bottom rack.
Tilt washer on it's side.
Remove wire connections to heater element (They slide right off but make sure to remember which one goes where)
Unscrew the nuts that are holding the element on. I used some pliers. It wasn't difficult.
Remove old element and replace with new.
Reverse order.

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

I'm a stay-at-home mom of 3 kids, so I enlisted the help of my oldest son (5 years old) for this job while the 2 little ones were asleep! First we cut the power to the dishwasher, then we removed the 2 bottom screws on the stainless steel front and slid it off to expose the back of the dispenser. We removed the red and white wires from the left side of the dispenser, took out the 6 screws holding the dispenser in place, put in the new dispenser, hooked up the red and white wires (in the right order), and flipped the breaker back on! We ran a cycle to make sure it worked, and it did!! My husband was thrilled! He thought for sure we needed a new dishwasher! :o) Thank you, PartSelect!

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

Removing two screws on the inside of the door alows the outside panel to slide down and detach. The soap dispenser connects with six screws and two wires. Remove the dispenser through the inside of the door. Replace, reattach and reasseble in 15 minutes.

Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

Removed old spray arm, fitted new spray arm. VEry easy. Sorry I didn't do it months ago

I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down kinda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).

First I shut off the power to the dishwasher from the breaker panel. Then I removed the five screws holding the plastic top panel to the door (on the frigidaire, there is no need to remove the entire stainless steel door panel). I removed each of the four wires from the old latch (pulling the wires off required some "oomph") one by one and plugged them into the corresponding position on the new one. I did this so I would be sure to have them in the right place. I used a torx screwdriver to remove the two screws holding the old latch. I then replaced the old latch with the new one, replaced the top panel of the door, turned the breaker back on and everything was as good as new! The whole operation took maybe 20 minutes. It couldn't have been easier. The only surprises were how difficult it was to pull the wires off and the fact that the screws holding the latch were torx head.

In future, when I need parts, I will definitely use PartSelect. I have gotten parts from other sources, and this is the first place where, along with the part, you get all this advice from other DIY'ers. It's an absolutely brilliant idea and a lot of help.