Models
>
TB2040XP
TB2040XP Troy-Bilt Trimmer - Overview
Models starting with TB2040XP
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Carburetor
PartSelect #: PS9119300
Manufacturer #: 753-06190
It is an authentic manufacturer-sourced replacement part that i supplied for Craftsman trimmers. The function of a carburetor is to mix the air and the gas into a highly combustible mix before it goes...
$33.36
In Stock
Pawl Assembly
PartSelect #: PS9457214
Manufacturer #: 753-06091
The pawl assembly is a complete OEM kit that includes the two plastic pawls, the two springs, and the metal housing. Installation is rated "Medium" difficulty and requires a screwdriver and socket set...
No Longer Available
Fuel Tank Assembly
PartSelect #: PS9118306
Manufacturer #: 753-06250
Fuel tanks are responsible for storing and supplying fuel, like gasoline, for an engine. This fuel tank assembly is designed for and compatible with various models of trimmers and includes the plastic...
$20.61
In Stock
Clutch Assembly, Small
PartSelect #: PS9303676
Manufacturer #: 753-05860
This clutch assembly is a genuine OEM replacement kit for outdoor lawn equipment. The kit includes the clutch drum, clutch, clutch washer, and screw. The clutch assembly transfers power from the engin...
$24.11
In Stock
Carburetor
PartSelect #: PS10009632
Manufacturer #: 753-06288
This carburetor is supplied by the original manufacturer as a replacement part for gas trimmers. It is made up of a metal body and plastic choke lever. The carburetor is responsible for mixing air and...
No Longer Available
Switch
PartSelect #: PS10014381
Manufacturer #: 791-182405
This Switch is a black, plastic on/off switch for a trimmer. Installation of this manufacturer-certified switch is rated as "Easy" and requires a screwdriver, wrench set and socket set. Refer to your ...
$9.96
In Stock
Common Symptoms of models starting with TB2040XP
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
string trimmer would not start
emptied fuel from tank. pulled off the 2 fuel lines from the carburetor.opened the air cleaner door. removed the 2 torque screws that hold on the carburetor. removed the carburetor and air cleaner gasket. installed new carburetor and gasket and put back and tightened the 2 torque screws. closed air cleaner door and pushed the fuel lines o
... Read more
nto the new carburetor.put some fuel in the tank. started the trimmer. runs great.
Read less
Parts Used:
-
john from SHARPSVILLE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Carburetor replacement
Removed 2 screws securing the air cleaner and carburetor to the engine using a T25 Torx driver. then removed the throttle cable from the carb.Then removed the o ring gasket from the engine and replaced with a new one and replaced the carb etc. Primed it and fired it up.Runs just like new.
Parts Used:
-
William from PALMETTO, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Trimmer Would Not Start
The replacement of the carburetor, O-ring, and gasket was simple. I removed 2 screws that held the air cleaner and carburetor in place, swapped them out, and replaced the screws. What took longest was finding a piece of fuel line after breaking one of them. It was brittle after hanging in my garage for several years. I found some in my
... Read more
garage and replaced it. It took a few pulls to get it started, but ran very smooth.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
Read less
Parts Used:
-
Ricardo from FORT WORTH, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!