Models > SWT220WM

SWT220WM Speed Queen Washer - Overview

Sections of the SWT220WM

[Viewing 21 of 21]
Keep searches simple, eg. "belt" or "pump".
Thrust Washer – Part Number: WP233520
Thrust Washer
★★★★★
★★★★★
(2)
PartSelect #: PS11740482
Manufacturer #: WP233520
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found...
$5.52
  In Stock
Retaining Ring – Part Number: WP23748
Retaining Ring
PartSelect #: PS11740487
Manufacturer #: WP23748
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place o...
$9.71
  In Stock
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.52
  In Stock
Hose Clamp – Part Number: WP596669
Hose Clamp
★★★★★
★★★★★
(1)
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$5.52
  In Stock
V-Style Spin and Agitate Belt - 28-3/4 inches long – Part Number: WP27001006
V-Style Spin and Agitate Belt - 28-3/4 inches long
★★★★★
★★★★★
(2)
PartSelect #: PS11740577
Manufacturer #: WP27001006
This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.
$32.45
  In Stock
Hose Clamp – Part Number: WP285655
Hose Clamp
★★★★★
★★★★★
(2)
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$10.76
  In Stock
Lid Hinge Mounting Screw – Part Number: WPW10119828
Lid Hinge Mounting Screw
★★★★★
★★★★★
(2)
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$5.52
  In Stock
Complete Hub and Seal Kit – Part Number: R9900552
Complete Hub and Seal Kit
PartSelect #: PS2174602
Manufacturer #: R9900552
This kit comes with hub, seal head, gasket, seal shroud, seal seat, screw, spline insert, drive bell and seal.   No Longer Available
Wave Washer – Part Number: Y504082
Wave Washer
PartSelect #: PS2200824
Manufacturer #: Y504082
  No Longer Available
Inlet Hose Washer – Part Number: WPY013783
Inlet Hose Washer
★★★★★
★★★★★
(1)
PartSelect #: PS11757437
Manufacturer #: WPY013783
This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal...
$5.52
  In Stock

Questions And Answers for SWT220WM

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the SWT220WM

[Viewing 11 of 11]
Noisy
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Burning smell
Fixed by
these parts
Show All
Will not agitate
Fixed by
these parts
Show All
Pumps but will not spin
Fixed by
these parts
Show All
Will not stop filling with water
Fixed by
these parts
Show All
Spins slowly
Fixed by
these parts
Show All
Will not drain
Fixed by
these parts
Show All
Shakes and moves
Fixed by
these parts
Show All
Lid or door will not open
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Seal On The Bottom Of The Tub Was Leaking
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forward. Primed the pump and started the machine for the stated time and was a sucess.
Parts Used:
Complete Hub and Seal Kit
  • HOWARD from CORTLAND, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
32 of 40 people found this instruction helpful.
Bearing went out causing lots of noise.
This is not a bad repair, but give yourself some time. I did not have to take the tranny and motor out, but the inner and outer tub and all related parts had to come out, along with the outer tub base. If you are replacing the tub bearing, you HAVE to order the seal kit. Don't try to skimp like I did, since you will need the seal kit as this is what causes that bearing to fail in the first place. We forgot how quiet the washer was after I fixed it, and it saved us from buying a new washer since we were ready to say the heck with it and buy a new pair. You might need an 1.5 inch socket to get the big nut off the spindle, but I was able to get with a visegrip and hammer. The nice thing about this repair is even if you screw it up, you won't have water all over the place because of the seal design. I just checked under the washer a few times for the first few weeks and all seems fine.
Parts Used:
Main Tub Bearing Assembly
  • mike from hull, IA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
23 of 25 people found this instruction helpful.
The washer tub seal leaked
After removing the agitator and drive bell by pulling on them HARD, I found that the lock nut and hub were corroded in place. I used grinding wheels to remove them which took over an hour. The internal and external threads needed to be cleaned up with tap and die and the splines had to be filed in order to get the new hub on the shaft. I did not use antiseize compound. The tub seal went on easily and the lock nut was guestimate torqued using a wrench made for water heater elements. The drive bell seal was very stubborn. It is normally pressed on with a special tool, but I had scrap pipe sections that fit the inner and outer press-points and used a large hammer to drive it into place. The washer does not leak any more. Total time was around four hours.
Parts Used:
Complete Hub and Seal Kit Lock Nut
  • Gerald from Seminole, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Wrench set
17 of 19 people found this instruction helpful.