Switch to Classic
Models > SWT220WM

SWT220WM Speed Queen Washer - Overview

Models starting with SWT220WM

Keep searches simple, eg. "belt" or "pump".
Thrust Washer – Part Number: WP233520
Thrust Washer
★★★★★
★★★★★
(2)
PartSelect #: PS11740482
Manufacturer #: WP233520
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found...
$7.54
  In Stock
Order within the next 12 hrs and your part ships today!
Retaining Ring – Part Number: WP23748
Retaining Ring
PartSelect #: PS11740487
Manufacturer #: WP23748
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place o...
$13.26
  In Stock
Order within the next 12 hrs and your part ships today!
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.54
  In Stock
Order within the next 12 hrs and your part ships today!
Hose Clamp – Part Number: WP596669
Hose Clamp
★★★★★
★★★★★
(1)
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.54
  In Stock
Order within the next 12 hrs and your part ships today!
V-Style Spin and Agitate Belt - 28-3/4 inches long – Part Number: WP27001006
V-Style Spin and Agitate Belt - 28-3/4 inches long
★★★★★
★★★★★
(3)
PartSelect #: PS11740577
Manufacturer #: WP27001006
This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.
$37.19
  In Stock
Order within the next 12 hrs and your part ships today!
Hose Clamp – Part Number: WP285655
Hose Clamp
★★★★★
★★★★★
(2)
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$10.76
  In Stock
Order within the next 12 hrs and your part ships today!
Lid Hinge Mounting Screw – Part Number: WPW10119828
Lid Hinge Mounting Screw
★★★★★
★★★★★
(2)
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$6.54
  In Stock
Order within the next 12 hrs and your part ships today!
Drain Hose with Rubber Elbow – Part Number: WP40053901
Drain Hose with Rubber Elbow
★★★★★
★★★★★
(4)
PartSelect #: PS11742254
Manufacturer #: WP40053901
This hose attaches to the pump to help remove the water out of the washer. 7 feet in length.
$44.44
  In Stock
Order within the next 12 hrs and your part ships today!
Complete Hub and Seal Kit – Part Number: R9900552
Complete Hub and Seal Kit
PartSelect #: PS2174602
Manufacturer #: R9900552
This kit comes with hub, seal head, gasket, seal shroud, seal seat, screw, spline insert, drive bell and seal.   No Longer Available
Wave Washer – Part Number: Y504082
Wave Washer
PartSelect #: PS2200824
Manufacturer #: Y504082
  No Longer Available

Common Symptoms of models starting with SWT220WM

[Viewing 11 of 11]
Noisy
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Burning smell
Fixed by
these parts
Show All
Will not agitate
Fixed by
these parts
Show All
Pumps but will not spin
Fixed by
these parts
Show All
Will not stop filling with water
Fixed by
these parts
Show All
Spins slowly
Fixed by
these parts
Show All
Will not drain
Fixed by
these parts
Show All
Shakes and moves
Fixed by
these parts
Show All
Lid or door will not open
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water leaking on floor from "mysterious place underneath washer"
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

So, I finished draining, removed the hose (required pliers to squeeze off a hose clamp).

Upon inspecting the hose, it was also apparent that the hole was caused by rubbing against a support bracket for the motor. This should not happen, but it did because the plastic standoff supposed to keep the hose away from the bracket was installed 180 degrees backwards.

So, I simply replaced the hose and turned the bracket around to the correct orientation.

Everything worked as planned and my repair cost was much less than if I had called someone out.
Parts Used:
Drain Hose with Rubber Elbow
  • Bryan from Chicago, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
47 of 52 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Seal On The Bottom Of The Tub Was Leaking
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forward. Primed the pump and started the machine for the stated time and was a sucess.
Parts Used:
Complete Hub and Seal Kit
  • HOWARD from CORTLAND, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
32 of 40 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bearing went out causing lots of noise.
This is not a bad repair, but give yourself some time. I did not have to take the tranny and motor out, but the inner and outer tub and all related parts had to come out, along with the outer tub base. If you are replacing the tub bearing, you HAVE to order the seal kit. Don't try to skimp like I did, since you will need the seal kit as this is what causes that bearing to fail in the first place. We forgot how quiet the washer was after I fixed it, and it saved us from buying a new washer since we were ready to say the heck with it and buy a new pair. You might need an 1.5 inch socket to get the big nut off the spindle, but I was able to get with a visegrip and hammer. The nice thing about this repair is even if you screw it up, you won't have water all over the place because of the seal design. I just checked under the washer a few times for the first few weeks and all seems fine.
Parts Used:
Main Tub Bearing Assembly
  • mike from hull, IA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
23 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!