SWSG1031HQ4 Westinghouse Washer Dryer Combo - Instructions

remove old belt, install new belt

Good

Took apart dryer and replaced limiter located on back, reassembled dryer and tested wiithout connecting to vent. Dryer working fine without vent connection. However as always something simple turns to disaster when children help. While cleaning out lint from dryer vent which I will say was the original problem causing the limiter to trip, youngest son wanted to help. Son did not know that to walk in an attic you must step on joists not drywall. No one was hurt just banged up falling into the garage. Extended repair to ceiling added dificulty factor of 2 days and a bit of insulation clean up. Good news is the dryer works fine and the vent is no longer clogged up with lint. Watch your help it always adds to the repair.

i folow the instructions from web page

Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!

opened top of dryer, remove blown part and installed new part very easy.

removed top-removed front-removed belt-removed drum (I didn't know how the drum came out WITH the bearing so I unscrewed the 3 middle screws on the back of the drum which released it from the bearing)- removed the bearing-that was when I knew what to order. installed the bearing on the drum before assembling all in reverse order. I wasn't sure how much grease to use so I used about 1/3 of it.

Was so easy the video link made it even easier. Will with no doubt return for any other problems for my appliances if needed.

I turned off water valves. I then unplugged the AC. I took the 4 screws out on the back end of the top cover of the washer. I removed the two water lines from the water inlet vales and the two electrical connectors. I then removed the two screws holding the water valve assembly and it came out easy. Installed new water valve assembly mounted with two screws , then put the electrical connection and water lines back on new water valve assembly. I turned the incoming water vales on and installed the top cover with the four back screws and was done.

Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!

This repair took about fifteen minutes. I popped the top of the dryer using a flat-blade screwdriver, leaned it back against the back wall, unscrewed two screws holding the front panel, removed the five electrical spade contacts after marking which went where, swung out the panel and lifted it off. After that, it was a simple job to unscrew the plate holding the solenoids in, at the bottom left of the unit. I replaced the solenoids, closed everything up and now the dryer is working better than it has in the last three years, or so. If your dryer is heating sporadically, the odds are 85%, or more, that a solenoid swap-out will correct the problem.

Very simple. Pop the top open released the beld from the back it's easier that way the video was very helpful the sound was so bad you can hear it from a few houses down after year of just using it like that I figured I ha d nothing to loose great price great instructions now it sounds just as new.

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

Remove the agitator and the 2 bolts that clamp the spin drum to the shaft and pull up on drum the 2 seals are on the shaft right there. Pry up on the seals to remove them. Install all seals and Be sure to completely clean all parts before putting them back in the machine and re assemble the machine. The bad part of this job is if you have used powdered soap it took 3 hours to clean the parts before reassembly.

I viewed a video online and my repair was as simple as the video showed. Love that I am able to do quick fixes like this! Thanks Partselect.com!