SWSG1031DQ1 Westinghouse Washer Dryer Combo - Instructions

It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!

This is a front loader and the video I saw was a top loader. I removed the oval shaped centerpiece off the back to reach the pump. I also removed the filter and cleaned it, I used screw type hoseclamp in place of the tension spring for easier assembly due to the cramped space. This helped the drain problem as did cleaning the filter. The no spin problem persisted and I ordered the door lock part. This part fixed the no spin problem.

Part Select got me the right parts in the agreed time--good job. Shut off the power or unplug the dryer which ever is easiest. The toughest part of doing this job was figuring out how the lid came off the dryer, if you have a jack knife or a putty knife you push it in between the top of the dryer and the body about an inch below the dryer top and about six inch from both sides of the dryer front you will hit a latch that releases the top--slip a screw driver into the opening and do the other side. The top can be removed or you can hold it open with a stick. There are two screws that you need to locate they are on the inside of the dryer front about 9" from the top one on each side they are all that hold the front on the body so remove them but carefully not to drop them inside the dryer. On my dryer there were two screw inside the dryer door that held the filter body onto the front that had to be removed too. Then push the screw driver between the front and the body of the dryer like the top and it will pop open. There are some wires going to the front from the body they can be unplug just follow the wires to the connection point. On mine, I squeezed the sides of the connector and the wires pulled apart. Now you can move the front aside. At the lower right in the body you find the valve and heater burner. On top of the valve there are two sets of wires coming off the valve. Disconnect the wires--one set is for a three wire connection the other for two wire connection. Your parts have a two wire coil and a three wire coil. The coils are freed by unscrewing the metal cover that holds them down remove the two screws and that cover then remove the old coil off the valve then replace the new coil with the part that is the same. Three pin coil with three pin coil positioning in the same way as the old coil, then do the other one. Reattached the metal cover with the screws and put it all back together in reverse order. The dryer chamber--the inside of the dryer rests on the front so when you put them together you may have to lift the chamber up to met the face a little (1/4"). Good luck.

Watched the handy-dandy video, removed the defective part, waited for delivery, installed the new part and was back washing another load (minus the wet floor) in less than 10 minutes! Just one catch, I am a 56yo female with nominal hand strength, so technically, I had to recruit the help of a (stronger) person to tighten-up those self-tapping screws. I didn't feel so weak when I noticed that he had some difficulty as well. LOL! Ladies, don't be shy asking for help-I even tried the power drill with no success. Excellent video! Aside from the self-tapping screws, my grand-daughter could have managed this repair!

For the washer/Dryer combo, replacing water valve was easy, first you need to remove washer front panel and top lid, make sure that washer electrical is unplugged, turn off gas, turn off water valves.remove 1-screw holding water valve. reaching from top and using pliers remove retention clip holding hose. remove old water valve, there are two electrical connections for cold and hot water valves, make sure you mark them, remove them from old water valve. insert new water valve, connect hose and make sure that retaining clip is connected correctly.connect electrical wires. screw water valve into place from rear of washer. connect water hoses. before connecting panel and lid, turn on water valves and observe if there is any water leaks.

Took off the front panel and changed the belt. Putting on the front panel took longer then changing the belt.

Remove front panel, controls and the whole front of the dryer. Split blower housing and remove blower fan. Slide new fan on shaft with flat side aligned and make sure tabs on the fan go into the groove on the shaft. Install clamp, and reassemble blower housing. Test operation by spinning dryer drum.

The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.

remove old belt, install new belt

Good

i folow the instructions from web page

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!

removed top-removed front-removed belt-removed drum (I didn't know how the drum came out WITH the bearing so I unscrewed the 3 middle screws on the back of the drum which released it from the bearing)- removed the bearing-that was when I knew what to order. installed the bearing on the drum before assembling all in reverse order. I wasn't sure how much grease to use so I used about 1/3 of it.

Was so easy the video link made it even easier. Will with no doubt return for any other problems for my appliances if needed.