Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SWS1233HS1 > Parts

SWS1233HS1 Westinghouse Washer - Parts

All parts for the Westinghouse Washer SWS1233HS1

Below is a list of all parts for the Westinghouse Washer SWS1233HS1. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the SWS1233HS1
15-28 of 102
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$50.21

Spin Bearing

The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, theref...

$8.72

Upper Spin Bearing Washer

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.

$9.53

CLAMP

Clamp used for hoses.

$29.98

Horizontal Spring

This is a horizontal spring, but you may know it as a suspension spring, and it is a part for your washing machine. Its function is to stabilize the outer tub by keeping it balanced. In order to make this repair you will need a putty knife, and a Phillips head screwdriver. This spring is roughly 1 inch thick by 4 inches long, it is chrome colored, and has two hooks on either end to make your repair easier. Take note that this piece is sold individually.

$8.53

SPRING

$6.17

Agitator Screw

This is the bolt (screw) that holds the agitator in place.

$30.97

Splash Cover Seal

The tub ring seal or splash cover seal is used for washers. This part seals the tub cover to the outer one and prevents water leakage from around the tub ring. If your seal is dama...

$30.82

Tension Spring

This tension spring works in conjunction with the idler pulley. The spring is part of your top load washing machine assembly. The most likely reasons for needing to replace the tension spring is if you notice that your washer is not spinning or agitating, the drive belt has come loose, and the idler pulley is no longer secure. To access this part, you will need to remove the front of your washer. The spring is located underneath the bottom of the tub. This is a genuine OEM part that comes right from the manufacturer.

$7.67

Agitator Spacer

Use in conjunction with the agitator screw.

$40.86

Water Inlet Hose Assembly

This water inlet hose is used in washers. The hose connects the washer water inlet valve to the water supply in your home. There are two solenoids on the valve, which are referred to as coils, and there are two wires attached to each solenoid that should be labelled to ensure they are properly reconnected after replacing the new hose. Over time, your hose can begin to leak which can lead to floods. Replacing your hose earlier on can prevent this problem. Refer to the diagram provided by the manufacturer for installation instructions. Remember to unplug your appliance from the power source before beginning this installation project.

$8.91

SPRING

$7.15

Screw - Sold Individually

$37.43

Pump to Tub Hose - Black

$27.77

Lid Strike - White

This part is used to activate the lid switch when the lid opens/closes.

All Parts for the SWS1233HS1
15-28 of 102