SVD48600PC Jenn-Air Range - Instructions

I removed teh pans and great filter.

I removed the screws from the older Rear and front burner assembly and use them on the new parts. It just took about 20 mins to do all 4 burners.

Checked that the gas worked for all 4 burnes once assembled. Then replaced the pans and the grease filler.

Results have been great as the gas burners ignite faster and the stove top looks brand new :-)

Remove burner knobs, Removed 7 screws from bottom of face plate. Removed screws from 2 alluminum or steel spacers I guess you could call them. I let the Op Panel hang carefully not to stress wires. I marked all wires of the Latch asm. Removed the four screws holding it in and carefully removed the wires. Replaced in opposite manner and self cleaning works. The oven tried to start the cycle but I noticed the latch never triggered. When the function first stopped working I was able to apply slight force to the door and the latch fired. So after replacing the door switch it still failed to work. So latch asm was the official fix. So I have had to replace the latch asm and the Op Panel for being dim. I don't think this model is very good. But Partselect.com is great easy to find parts and good prices. Very pleased with my experience.

Removed Door- Removed outer stainless cover(6 screws) Removed the 1st 2 glass pieces. realized that there were 4 pcs of glass, not 2 as I thought. Found 2nd assembly of 2 pcs, of glass. The piece i ordered that was called inner actually only fit on the inside of the the two outer pcs, too small to replace what was the outer piece on the inside of the door. Called, returned 1st piece, got the correct one and reassembled.
Would have been easier if parts had more understandable labels such as inner door outside glass etc
beware when you order!

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

I didn't. Don't know how to get to light bulb to change it for this specific model

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

I inserted the door strikes in the proper position and then snapped the panel in place.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

None of the surface burners (two Uni-burners) would light without using a match. I first ordered two replacement PS2089818 top burner spark electrodes. I replace one which was very easy - the electrode just clips into the burner - and I traced the wires down to the back bottom of the stove where I found they plugged into an ignition module. The new electrode didn't help, but since all four burners were out it made sense that the ignition module would be the problem and not the two separate electrodes. So I ordered a new ignition module. It plugged in easily with the terminals well marked like the original. I put the original electrode back in and all four burners now light properly with the desired "tic tic tic" sound with the knobs in the "high/light" position.

repair was simple, removed a total of 8 screws and seperated the two door panels to replace the 2 hinge assemblies. I spent more time degreasing the door and window then replacing the hinges.

Replace filter

I rremoved two screws and pulled element out about 3 inches. I un hooked the two wires and tested with an ohnm meter to determine the condition of the element. Element was bad so I ordered a new one. Service and price were great. Easy fix. Thank you.
Don't forget to unplug first.

The door seal was an exact fit for the factory one. There are little clips that hold the seal to the door. The clips are already installed in the seal. To remove just grasp the seal at each clip and pull up. The seal comes off easily. The ends of the seal are tucked into holes at the bottom of the door so you can just pull them out. For the installation of the new seal grasp the seal at each clip and push them into the littles holes. I used a flat blade screwdriver to tuck the seal ends into the two larger holes at the door bottom. The whole process took about 10 minutes.

I wouldn't have changed the seal but the hot lasagna made the seal sort of hard after it cooled off.