SVD48600B Jenn-Air Range - Instructions

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

throw the old one in the garbage, drop in the new one. It is about 3/4" narrower than the one that came with the stove but still covers the down vent adequately

Removed old filter, dropped in new filter. A breeze! What was best of all, is that Parts Select shipped the filter immediately and it arrived within just a day or so! Well done!

The issue: the burners were abused by the previous tenant, the burnt grease was clearly visible. They would hardly ignite and the smell of gas was always present.The remedy: new burners. They were hard to find, I was not completely sure about to stove model (it could be quite a search to find the right ones). There is a front burner and a back one. I was not sure from the diagram about the back one, so I called Partselect and someone answered the call right-away. The burners arrived a few days later, and they were the correct ones. The burners are not Jenn-air specific, it looks like several brand names use the same ones. The installation was extremely easy, a few hex screws. The stove is like new. I highly recommend Partselect.

The new replacement grease filter came without damage and it was a simple task of removing the old and setting the new in it's place. No tools were required.

Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill

I followed the first instructions that were listed on your site. Except I didn't need to remove the screws on each side of the turn on knobs. I just removed the knobs and then found out that I didn't even have to do that. The whole panel came down and I rested it on other pans so I could unhook the "cables" to the board. The most trouble I had was trying to unhook those cables. BUT once done, the job was a cinch. "I AM WOMAN - HEAR ME ROAR." Yes I did it all by myself and am quite proud of it too. Thanks so much for the instructions. VERY, VERY, helpful. Probably saved over $125 in service call-plus the markup of the dealer.

Very simple project. Had no clue it was so easy! To test how easy it is, remove the left side grill parts, move the grill parts from the right to the left! I had no idea there was a micro switch in the cooktop to change the fan operation! Parts arrived quickly. Only received one grate of the set, this was quickly fixed by Parts Select Customer service! We only used the grill once, made such a mess! Why did I wait so long to do this! (Over thirteen years!)

Read previous repair story

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Lifted the old one out and put the new one in. Very easy