Models > SVD48600B > Instructions

SVD48600B Jenn-Air Range - Instructions

All Instructions for the SVD48600B
46 - 60 of 351
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Simply needed a new knob, however...
However, I was very happily surprised how fast I got the part even though I did not specify fast shipping.
Parts Used:
Gas Valve Knob
  • Shane from Dallas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Changing over from LPG to Propane
In oven I unscrewed orfice; replaced with new orfice. On stove top the people who make it sent a kit for $11.00, plus S & H. I installed it as per instructions.
Parts Used:
Natural Gas to Liquid Propane Conversion Kit
  • George W from Carlsbad, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
10 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Display was very dim.
Very easy to locate parts on your web site. I also ordered new burners and a new control pad for the front. I think I will get 10 more years out of this stove. It's like new. I will keep this web site in my favorites list. Thanks Moe
Parts Used:
Electronic Clock Control Board
  • Louis from Baton Rouge, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lcould not see the lights on the clock or temperature on the control panel
The parts came with no instructions, we started to take off , the front panel , finally took off the 4 screws under the panel, then the two small ends caps on either side. the only problem we had after being carefull to study the part as we took it off , was the ribbon strip, that stayed connected to the stove. after we tried to put all back together, the exhaust fan kept coming on. There are two small
holes that need to be aligned in the replacement part. also to get the strip out and back in you need to press and pull up on the small black notches on either of the strip.
Parts Used:
Door Latch Assembly Electronic Clock Control Board
  • charlette from FREDERICKSBURG, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler blement failed
Sunday, four days before Thanksgiving, our oven would not bake properly. A quick check indicated the top element was not working. What to do? Where to get a part in time to fix for Thanksgiving dinner? The answer was easy - PartSelect. I had the part in my hands on Tuesday AM. Oven was fixed in 15 minutes and my wife was baking pies within an hour. All worked well and yes, we had a wonderful trukey dinner. Great service !
Parts Used:
Broil Element
  • Donald from Hudson, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My oven would either turn off or on by itself
I deduced that it had to be a major computer part and when I e-mail parts select, they concurred. I got the part and had my repair guys come install it. It did not work when he finished after three hours. after another mother board was sent a friend carefully installed it with me recording the lineup of the wires and calling them out to him. when he took the other board off he found a bad port, that did not fit well. it is now working beautifully and I got to bake all my cookies and bars for the holidays! Thank you Parts select for you help and your forum! couldn't have done it without you!
Parts Used:
Bake/Broil/Convection Relay Board
  • Elaine from Jacksonville, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Self cleaning would not work on the oven
Removed old part with a pair of pliers and plugged the new part into place.

Very simple and the self cleaning feature works again.
Parts Used:
Door Lock Switch
  • Crucita from Albuquerque, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Downdraft Blower Failure
Blower motor stopped working and the breaker tripped. Horrible smell! from the somewhere in the oven. Looking at the wiring diagram told me that there was a relay board feeding he motor, but I had no idea where it was, which took a little Internet searching to find it. Finally seeing that it was in the rear I was happy to see that there was enough flexible gas line to pull out the stove enough to check the board, which was fried. I replaced the board and then looked for the reason it smoked and found that the blower motor was shorted (and stank horribly).
It was straighforward to replace, but when I put everything back, NOTHING worked at all - no lights on the control panel, nothing. I then checked the voltage across the terminals and saw 240V and was puzzled until saw that there was no 120V to neutral where the plug connected to the back of the stove. The outlet, however, had 120V to neutral. Since it was a molded plug I thought that was not likey to be a cmmon failure, so after killing th breaker I took off the outlet cover that the stove plugged into and found out that the neutral terminal was intermittent.
The neutral contacts were not grabbing the netral terminal on the plug tightly enough and were a little discolored in one spot. All that moving around of the plug while moving the stove probably moved it just enough not to work at all - that thing was a fire hazard that I'm surprised hadn't been the cause of more damage in a house only 12 years old. Rather than try and clean the termnals and trust bending them to be tighter (and worry about metal fatigue) I spent the $10 so that I could sleep better for a tight new 240V 30A outlet.
Everthing works like a charm now.
Parts Used:
Blower Motor Urethan Foam Gasket
  • Steven from Marshfield, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
10 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
20 year old burners were slow to light and hard to adjust for our propane fired stove. And, they were scratched and ugly
Removed four screws; withdrew two burners; set two new burners in place; installed same old screws. That was it. When I turned them on to adjust the flame, they came on almost instantly and no adjustment was needed.

Wife loves the nice new look.
Parts Used:
Front Burner Assembly - Black (Glossy Finish) Rear Burner
  • thomas from Goodrich, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lighted display very dim to non existant
Thanks to JP in customer service.

TURN THE POWER OFF TO THE STOVE at the breaker box!
I had to pull all the burner knobs off (4ea) and remove the screw under each one. Then open the oven door and remove the screws holding a trim piece on and the hex head screws holding the "touch pad panel" on (was also held on by the screws I had already removed from behind the knobs) 1 smaller screw at each end (total of 2) under there hold the plastic trim on that needs to be moved slightly to let the panel come out. (DON'T OVER TIGHTEN WHEN YOU REASSEMBLE) You hang the panel in the 2 slots provided and remove the old display unit. Gently unplug the 2 wire harnesses and ribbon that actually connect the touch panel to the display PC board. Look for the 2 small holes in the ribbon that will line up with the female part on the board. A piece on the board where the ribbon plugs in will slide up a little and allow you to plug the ribbon in and then push it gently back down. Finish putting it back together and turn power back on at the breaker box. Works perfectly.
Parts Used:
Electronic Clock Control Board
  • Dan from Burlington, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part arrived broken.
Contacted customer service via email. Included a description of the problem as well as a photo that clearly showed that the Front Burner Assembly was, in fact, NOT an assembly when it arrived.

Nobody even acknowledged my email.
This was a $140 assembly.

Never again will use these guys for repair parts.
Parts Used:
Front Burner Assembly - Black (Glossy Finish) Rear Burner
  • Thomas from HOLLISTON, MA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    30 - 60 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Parts Used:
Main Power Terminal Block
  • Dana from Black Mountain, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Parts were worn and dated.
I removed teh pans and great filter.

I removed the screws from the older Rear and front burner assembly and use them on the new parts. It just took about 20 mins to do all 4 burners.

Checked that the gas worked for all 4 burnes once assembled. Then replaced the pans and the grease filler.

Results have been great as the gas burners ignite faster and the stove top looks brand new :-)
Parts Used:
Double Burner Pan - Black Rear Burner Front Burner Assembly - Black (Glossy Finish) Grease Filter
  • Judy from San Jose, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Self Cleaning did not work.
Remove burner knobs, Removed 7 screws from bottom of face plate. Removed screws from 2 alluminum or steel spacers I guess you could call them. I let the Op Panel hang carefully not to stress wires. I marked all wires of the Latch asm. Removed the four screws holding it in and carefully removed the wires. Replaced in opposite manner and self cleaning works. The oven tried to start the cycle but I noticed the latch never triggered. When the function first stopped working I was able to apply slight force to the door and the latch fired. So after replacing the door switch it still failed to work. So latch asm was the official fix. So I have had to replace the latch asm and the Op Panel for being dim. I don't think this model is very good. But Partselect.com is great easy to find parts and good prices. Very pleased with my experience.
Parts Used:
Door Latch Assembly
  • Rick from Beaverton, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench set
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The range burners would not catch a spark and ignite. They would just keep clicking with no ignition.
I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exposing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.
Parts Used:
Surface Burners Spark Module Kit
  • Adrienne from Lake Havasu City, AZ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the SVD48600B
46 - 60 of 351