Models > SVD48600B > Instructions

SVD48600B Jenn-Air Range - Instructions

All Instructions for the SVD48600B
1 - 15 of 351
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Grease Filter
Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.
Parts Used:
Grease Filter
  • Gene from Washington C.H., OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
520 of 528 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Parts Used:
Long Oven Sensor
  • David from Westford, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
145 of 173 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost all clock and timer display
Removed the 4 phillip head screws that hold the trim plate on the bottom of the display panel (and you probably could skip this step).
Next, I removed the knobs from the front of the display panel.
Then I removed the 4 phillip head screws that were located (1 each) behind the knobs.
Finally, I removed the 4 hex head screws from the bottom of the front panel.
You caan then remove the panel a few inches and remove the two cable connectors.
The trick part is to get the flat ribbin cable disconnected. If you squeeze the two small tabs (one on each end of the connector), the connector moves up and spreads open to CAREFULLY remove the ribbon cable.
The clock assembly has just two hex head screws holding it in place. Remove them, and reassemble everything in reverse.
If you did everything correctly, you should have a very bright stove clock again!
Parts Used:
Electronic Clock Control Board
  • John from Kuna, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
84 of 90 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace filter
Just placed it at the filter location. Liked the ring feature on the filter for ease of removal for cleaning. My previous ones didn't have such feature. Thank you for filling my order. I bought an extra filter for the future. I'm a big user of my Jenn-Air range. I may soon be needing to replace my griddle. Will be contacting your company then.
Parts Used:
Grease Filter
  • Marie from New Smyrna Bch, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
98 of 162 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1-1 code
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.
Parts Used:
Long Oven Sensor
  • charles from marstons mills, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
68 of 89 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing bake element as oven wouldn't heat
After viewing the diagram on partselect.com, I knew this would be easy. I first shut off the circuit breaker to the oven, then used a phillips screwdriver to remove the two screws on the plate securing the element. Once removed, I disconnected the two wires, and removed the old element. I then connected the two wires to the new element, and screwed the plate back into place. I then switched the circuit breaker back on and tested the new bake element which was working perfectly. This do it yourself repair saved me time and money not having to call and schedule a repair man. Thank you so much partselect.
Parts Used:
Bake Element - 240V
  • Catherine from Allenton, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
47 of 51 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clock dimmed to very low, oven temp unreadable
Was about to spend 2000 on new oven and decided to check here. At least 15 stories with same problem and solved. Add one more.

Only thing new to me was ribbon connector. Didn't really pay attention when I disconnected from the old assembly. When you squeeze the ends of the connector, part of the connector itself rises up to release the ribbon cable. Remember this when reinserting the ribbon cable on new assembly. If I hadn't followed the "If you have to force it, it ain't right" rule it could have gone bad.
Parts Used:
Electronic Clock Control Board
  • Thomas from Moncks Corner, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
41 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old grease filter was bent and needed replacing
I simply lifted off the grille in the center of the stove, pulled out the old filter and dropped the new one in. It sits at an angle (right side down, left side up) rather than slotting in to a particular spot.
Parts Used:
Grease Filter
  • Linda from Palo Alto, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
69 of 130 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Repeated oven temperature sensor fault codes.
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.
Parts Used:
Long Oven Sensor
  • David from Arlington, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
33 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic clips had broken, causing bottom skirt piece to fall off.
After attempting to order this part from Whirlpool twice and twice receiving the wrong thing, found correct part on PartSelect in about one minute. Shipment came fast and the repair was very simple, under five minutes. You just pop the pieces in place and snap the piece back onto the oven.
Parts Used:
Single Door Strike
  • William from Greensboro, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
28 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
converting to LP gas
Replaced old parts with new ones.
Parts Used:
Natural Gas to Liquid Propane Conversion Kit
  • Paul from Elk Grove, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
30 of 40 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not shut down, kept heating
The front oven control panel was already in need of replacement. The digital readout had quit working sometime ago, so we began by replacing the control panel as well as the temperature probe. Neither of these items did the trick. Next I replaced the HI/Lo sensor switch. This replacement was a bit more labor intensive. Have to remove several screws and remove a large portion of the top of the stove. Once access is gained to the hi/lo switch, it takes (2) minutes to replace it. This of course did not take care of the problem either. Finally I replaced the bake/broil/convection circuit board. This was a bit of a job, only because of the amount of wires to and from this board. I litterally took a picture of the board (from this web site) and drew in the wires and marked them by color and noted where they went. I then merely unplugged each wire and with one screw, removed the board and installed the new one. After plugging in the wires as per my picture, SUCCESS. The board did the trick. Over all, it was not bad doing the work myself. I know we saved a lot of money my doing it ourselves. Just gotta have patience.
Parts Used:
High Limit Thermostat Electronic Clock Control Board Long Oven Sensor
  • curtis from Paris, IL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
26 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clock and all the readouts went "black". Stove still worked but no visible readouts.
First I turned off the electricity to the stove.
I then removed the 4 burner dials from the front panel. Then I removed the 8 screws under the front panel. Removed the triangle side pieces - 1 screw each. Slowly pulled the panel down and out and turned it face down so there was easy access to the back of the digital clock. Unscrewed the 2 screws that hold the clock and replaced it. New clock worked perfect. NOTE: Included in the repair - I cleaned and repainted where there was grease and rust.
Parts Used:
Electronic Clock Control Board
  • Donald from Sausalito, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Wrench (Adjustable)
25 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't heat the right temperature (you would have to add 100 degrees on to it)
Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.
Parts Used:
Long Oven Sensor
  • Claudine from Bethlehem, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
26 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Display Fading to Black - Clock & Oven Temp Unreadable
I did this job myself, but it might be handy to have a helper to assist in holding the control panel during unplug and replug stages of the process. Also strongly suggest you read through these and other posted instructions BEFORE getting started.

Kill Circuit Breaker Power To Unit.
Pull Four Burner Control Knobs off front panel.
Unscrew Phillips Head Screws from under each knob. (Be careful not to strip screw heads, I applied pretty firm pressure on screw driver to avoid stripping).
Open Oven door.
Remove 4 Phillips screws on trim piece under control panel and remove trim piece.
Unscrew 1 small Phillips screw on each side of panel to loosen plastic side trim pieces.
Use socket to remove 4 hex head screws holding control panel in place.
Gently pivot control panel top downward to access the circuit board panel. BE VERY CAREFUL NOT TO ALLOW CONTROL PANEL TO HANG BY FRAGILE CONNECTING CABLES!!!
GENTLY unplug the two white connector cables from the board. There is a locking tab on both that you can release with a fingernail or small flathead screwdriver while gently pulling the connector upward. (These connectors snap to lock more easily when you eventually re-assemble to the replacement board).
VERY GENTLY unplug the ribbon cable. This was a bit confusing to me at first, but if you gently squeeze the two very small tabs on both sides of the black connector, you can gently raise the center body of the connector upwards about 1/8 inch. (You might find it helpful to practice how this mechanism functions on your replacement part BEFORE you do the disassembly, it's really pretty simple once you see how it works). This will take the gripping pressure off the ribbon itself and you can gently wiggle the ribbon out free from the connector taking note of the two very small alignment holes in the ribbon connector as you do so.
Now with all cables free use a socket to remove 2 hex head screws holding the circuit board to the control panel.
Now install the replacement board by simply doing all above in reverse. Take care to line up cable connections to the board properly, noting the two alignment holes in the ribbon cable to tabs in the black connector. All three connections should snap in easily without undue force.
Your range display should be good as new.
Parts Used:
Electronic Clock Control Board
  • Robert from Portsmouth, NH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
19 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the SVD48600B
1 - 15 of 351