Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SGR341AQ2 > Instructions

SGR341AQ2 Westinghouse Dryer - Instructions

All installation instructions for SGR341AQ2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGR341AQ2
196-210 of 379
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The dryer made a clunking noise as it was turning

  • Customer: John from Largo, FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I used the PartSelect website to diagnose and repair the dryer. The video shown was a different model. Mine is a front loader. I just had to figure out how to get the top and front panels off myself. I just took my time as to not break anything. Once I did that the video showed me how to remove the belt tension and remove the drum and belt together. The hitch pin was a little different so I called to make sure the parts were OK. I then vacuumed out the cabinet installed the parts, the drum, reset the belt tension and then the covers. It sounded sweet when I started it up. Mission accomplished! $41 vs. a couple of hundred I suppose.

the rear drum bearing broke

  • Customer: Karen from Clairton, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
when the bearing broke the drum fell in the back. I tore the dryer apart, ordered the part and fixed it when the part came. the dryer runs like new now!

squealing, very noisy dryer!

  • Customer: Vern from Sedalia, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!

Loud squealing while drying

  • Customer: Brian from Brier, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The consensus seemed to be that the loud squealing was most likely the rear drum bearing needing to be replaced. Although the repair went very well (great video!), it did not fix the problem. BEFORE you go the route of replacing the rear bearing, first pop up the top and see if a little piece of plastic that is attached to the top middle of the front panel by a screw is rubbing against the drum (you have to have a load going). I removed this part (I could not find it listed on any parts list) and the squealing stopped. I have no idea what the purpose of this part is, except for maybe keeping the drum from dropping too far down if the load is really unbalanced. This plastic part is on the dryer that has the controls on the front (it has the ability to be stackable) and might not be on the other unit that has the controls on the top back. If anyone has posted this as a possible cause of the squealing, I haven't seen it.

Dryer had a bad sqeaking sound

  • Customer: james from mascotte, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I like fixing things for myself. So I looked the problem up on the internet. Found the repair tech that I needed. The found your parts site. And BOOM. Looked up mt part on your site. Very easy you had everything I needed. And you got it to me quick. THANKS. When the part hit my mailbox. Everything I needed was there. I pulled the plug. Fliped the lid up. Took off the front. Removed belt off the ideler. Removed drum replaced bearing assy. Put it back together. Closed the lid and pluged the unit in. Worked so well I felt like a pro. My wife was tickled pink. Just like a new one. Thanks guys for making me look good and saving me a lot of money. Will use this site again. I give you 2 thumbs up.

Started with an annoying squeaking noise until the shaft broke and the drum hit the floor, KTHUD!!

  • Customer: Cheryl from Tulare, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered the rear drum assembly on Monday evening and the part came on Wed at 11 am. I started the repair at 1 and finished at 3. It would have been faster, but my computer kept freezing during the repair video. The video was so easy to follow. I could have used longer arms or a helper, but I managed to get the job done by myself. Needless to say, my husband was thrilled. Great service. Thanks

Heating but drum not turning

  • Customer: Richard from New Orleans, LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
With drum not turning, I removed rear access panel and confirmed that the belt was missing from the motor pulley. The instructional video provided by PS was extremely helpful. It made the job simple. Removal of drum thru front frame was the most difficult part which was relatively easy. Once the front panel and drum were removed, I could then see that the front drum top glide nylon/felt strip needed replacing which I then obtained.

Rear bearing was squeaking

  • Customer: Robin from Lafayette, OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Repair went just according to the video except to pull the drum out there was a plastic lock at the front of the dryer. It was held in by one screw and easy to take off. When I pulled the drum out the armature and spring that hold the belt tight fell off. I panicked a little, but easily put the pieces back in place. When I started the dryer for the first time it sounded odd but realized it was the sound of all the grease spreading itself around the bearing.

drum would not turn

  • Customer: Paula from Tryon, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Opened top and screwed the front off. Put belt around drum. It took two times as my sweet husband put the belt on backwards the first time.

My dryer was squealing, which we ignored for awhile, then the dryer was beginning to have trouble turning.

  • Customer: Jennifer from Cincinnati, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video on your site which was very helpful and informative. The one thing that proved to be more difficult than it appeared in the video was reengaging the belt. Every time we tried to do it in the way the video showed, the tensioner arm would come off. The belt was very tight, even with that arm pulled back. We ended up just putting the drum part way in and then putting the belt on the arm and motor, and then stretching it over the drum. Perhaps because it was new, it was so tight. The rest was a breeze. Just followed the video. Was quoted $310 for this repair and I did it for $40! Thanks for your help and website! What a break in a terrible economy. You helped us out!

Heat would come on but not stay on.

  • Customer: Stephen from Plymouth, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Flame Sensor didn't fix it but, it was easy to replace. Unplug electric. Lift up the top and remove wires from switch and light switch. Remove screws that hold on the front and remove front panel by lifting up and out. Sensor is on the left side of the burner, held on with just one screw. EASY!

Broken drive belt

  • Customer: Thomas from Woodland, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Raised the lid, removed 2 little screws,slipped the front panel off, disconnected the safety switch, vacuumed everything, slipped on the drive belt and reversed my way out. It was way more easy than filling a grease gun!

Broken belt

  • Customer: John from Minot, ND
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove drum, replace belt, return drum

Cut belt

  • Customer: gary from little torch key, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the vidio from yor web site it was great without it i would still be trying to get done.

The Dryer would not lite

  • Customer: Thomas from Hixson, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the coils off and put the new one on thats all
All Instructions for the SGR341AQ2
196-210 of 379