Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SGQ2152HS1 > Instructions

SGQ2152HS1 Westinghouse Dryer - Instructions

All installation instructions for SGQ2152HS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SGQ2152HS1
256-270 of 372
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lint filter was broken

  • Customer: BeLinda from Indianapolis, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I did was insert the new one! Service was excellent. I received it in one day!!!

Door handle broke on one end

  • Customer: June from Wilmington, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I had to grip the broken piece that was still attached to the screw with a pair of needle nose pliers and then unscrew it from the back side. After taking the screw out of the other end,I just put the new handle on and screwed it in. Very easy!

Dryer was make a really bad squealing noise

  • Customer: Ken from Pinole, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Saw video on YouTube on how to change rear bearing. Followed what I saw and repairs were made with ease. our repair kit included all the parts (new bearing) and everything fit perfect.

The belt broke on a squeaky dryer

  • Customer: christopher van from Milford, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I raised the top up by releasing the two clips in the front edge with a small flat head screwdriver. I used a bungie cord to keep the lid from bending to far back. I removed the front of the dryer softly letting the drum rest on the insides. I carefully removed the drum by pulling upward to disengage the rear bearing and not damage the heating element. I then cleaned the entire inside of the dryer with a vacuum, brush, and some compressed air. I then replaced and greased the new plastic bearing cup, installed the drum, slipped the belt on, installed the front cover, and hooked up the belt through the access door on the rear of the dryer. Checked to see if the system looked ok and closed the lid. Worked great. I would order a front seal felt kit also if I was to do it again.

Dryer ran, had no heat

  • Customer: Tom from Essexville, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Your website was very helpful in narrowing down and diaganosing the problem. A continuity tester verified an open solenoid. Ordered Sunday evening, parts arrived Tuesday. Ignition coils drop in place with a holddown bracket and one screw. Wiring harness is reattached. Front of dryer is put in place followed by the top. Plugged in the dryer (it is just commom sense to have the power off). Started dryer, of course it ran WITH heat. The end of the story is HAPPY WIFE, HAPPY LIFE. Happy to do business with you. Tom , MI

Bearing And New Belt

  • Customer: steve from mountain home, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched the video on how to do the repair. Very good instuctions made the repair go smoothly.

Door would not close because of broken female latch.

  • Customer: Raymond Frattone from Richboro, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.

Loud squeaking noise

  • Customer: David from WASHINGTON, DC
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video. Very helpful. There is no way I could have done this on my own without that guidance. Parts in Rear Drum Bearing Kit included new screws and metal support parts that are shown as reused in the video. To install these parts, I had to hold the back plate in place. A big piece of masking tape did the job nicely. The only major problem was tapping the holes in part that attaches to the drum -- very difficult. Needed my best Phillips screwdriver, leather gloves, and a lot of hand strength to get it done. I had to slightly ream out one of the holes to make the last screw fit. Minor problem - the idler arm is not retained by anything. The idler pulley and arm both fell off when I reinstalled the belt. I guessed right on how to get them back on the machine.

loud squeek

  • Customer: Cheryl from Weirton, WV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed the Video instruction which were provided. Dryer works like brand new.

Loud Squeaking noise

  • Customer: David from Sioux Falls, SD
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Just followed step by step instructions from the video provided by Parts Select

replace rear bearing

  • Customer: Dwight from Milaca, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
This was a stacked washer and dryer combo and is a lot more difficult to repair, requiring a lot more to take apart and put back together.

Dryer Made Loud Squeal During Operation

  • Customer: BOB from PRATTVILLE, AL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I set up my laptop with the partselect video going. Laid out my tools and the individual parts that were in the kit. I watched the video a segment at a time, performing the tasks in the same manner that the instructor did. All together, the process took less than two hours, I had no questions or difficulties, and the repair process went flawlessly and successfully. I had never done anything more complicated on a dryer than replacing the hose before this. The sense of pride in doing a repair of this level myself, and avoiding paying someone ridiculous fees to do it, is beyond description.

latch broken

  • Customer: Lukas from Pasadena, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
pulled out old catch with old pliers and popped new one, simple.

Constant high pitch squeaking

  • Customer: Courtney from Washington, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took out drum which was the hardest part because Im short so I needed a little man power to lift it up then out.... Replaced entire bearing parts and belt.... You do need a nut driver for that but we ended up using plyers which worked okay.... All in all it was way easier than I thought it was gping to be.... Now it sounds brand new.

No heat

  • Customer: THOMAS from VINELAND, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Taking the front of the dryer off was rather easy. A two screws under the control panel and once the flap that separates the washer and dryer was removed there are 4 more screws to remove and release the control panel (disconnect wire harness and let panel hang). Once removed, two more screws separate the door/front of the dryer. Remove those and the 4 on the top front of the dryer. When completed the only restriction you have are bracket mounts. Just give a good tug and the front should separate from the body. Thereafter, the drum can be removed by removing the belt first. Reach to the back and depress the spring loaded pully by moving it to the right, releasing the belt. Let the belt hang while you unscrew the the drum screws, 3 located in a triangle pattern inside the drum. Remove them and the drum from out of the dryer. Straight ahead of you is the heater assembly. In my case, only the coil had to b replaced. So it was as simple as removing the old and in with the new. Reverse your disassembly to get reassembly.
All Instructions for the SGQ2152HS1
256-270 of 372