SGM466B Dacor Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old knob cracked and needed to be replaced
I feel very silly doing this. I'm 76 year old female and always, well most always did home my own home repair. This was a no brainer, a 4 year old child could do it......I just had to find the right replacement knob, order it and when it arrived I put it in the place where the first one was missing. :-) Just trying to be silly here....he he
Parts Used:
-
Joyce from HARRISON, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LOVE this stovetop and want to keep it as it works beautifully!
The main issue was getting actual knobs for a cooktop that is well over 21 years old. Clearly I am the first to really cook on it!
These are the proper fit. Two were broken. Easy to simply lineup and push down to install.
The main point I would like to make is the Wonderful Woman who took my call and basically searched for the knobs. Thank you Thankyou!
These are the proper fit. Two were broken. Easy to simply lineup and push down to install.
The main point I would like to make is the Wonderful Woman who took my call and basically searched for the knobs. Thank you Thankyou!
Parts Used:
-
Marcy Mahoney from GRAND JCT, CO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Flame was not even all around.
Cleaned the brass ring and replaced the cap.
New brass rings may be an improvement too.
New brass rings may be an improvement too.
Parts Used:
-
Keith from MIAMI, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator spin freely by hand. plastic splines striped out
remove cap on top of agitator, use socket with extension to remove bolt. pull up to remove old agitator, reverse order to install new part.
Parts Used:
-
kerry from WALKERTON, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator not working, Striped splines.
-
Thomas from PAYSON, AZ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The agitator was not spinning.
I took a straight screwdriver and popped off the cap on top of agitator. Then used a ratchet with an extender and loosened and took out the bolt in the agitator. Then pulled the agitator straight up and inserted the new one.
Parts Used:
-
Steven from BRUCETON MLS, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas burner knob broke
-
Bruce from FRIDAY HARBOR, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not agitate
Plastic "teeth" at top of agitator were completely worn off, allowing the agitator to spin freely on the shaft. Just remove the bolt that connects the agitator to the drive shaft (located under the top cap of the agitator), remove and replace agitator and you're all set.
Parts Used:
-
Doris from Faucett, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!