SGI5916 ((07)) Bosch Dishwasher - Overview
Sections of the SGI5916
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Rack Roller Wheel
PartSelect #: PS8727423
Manufacturer #: 00611666
This wheel is a dishwasher rack wheel designed for the upper rack of your appliance. The roller wheel is approximately 1.25 inches in diameters and includes the brushing you need for installation. It ...
$10.28
In Stock
Lower Rack Wheel with Clip
PartSelect #: PS8697067
Manufacturer #: 00165314
This dishrack wheel is designed for use on the lower rack of your dishwasher, it allows the rack to roll in and out of your appliance with ease. This roller wheel includes the locking clip required fo...
$18.54
In Stock
Door Seal
PartSelect #: PS8723143
Manufacturer #: 00494772
This seal is also referred to as a door gasket, and it is designed for use on dishwashers. It is installed on the door of the appliance, and it seals the space between the tub of the dishwasher and th...
$31.07
In Stock
Lower Door Seal
PartSelect #: PS8714648
Manufacturer #: 00432490
This door seal, also known as a door gasket, is an authentic manufacturer replacement part for your dishwasher. It is responsible for creating a watertight seal between the tub and dishwasher door and...
$43.12
In Stock
Dishrack Stopper Kit
PartSelect #: PS8697039
Manufacturer #: 00165254
A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack sl...
$12.02
In Stock
Drain Hose
PartSelect #: PS8703123
Manufacturer #: 00298564
This drain hose is designed for use in dishwashers. After the wash cycle is complete the water need to leave the dishwasher, this drain hose it carries the dirty water from the drain pump to the kitch...
$39.89
In Stock
Detergent and Rinse Aid Dispenser
PartSelect #: PS8722285
Manufacturer #: 00490467
This detergent and rinse aid dispenser is an important part in your dishwasher. It is located on the inside of the door and it holds and releases the detergent during the wash cycle of your dishwasher...
$148.09
Special Order
Check Valve
PartSelect #: PS8697043
Manufacturer #: 00165262
This check valve is a genuine OEM part that is compatible with several different makes and models of dishwasher. A check valve is designed to prevent the backflow of dirty water, food waste, and debri...
$17.31
In Stock
Inner Door Panel Screw Kit
PartSelect #: PS8695919
Manufacturer #: 00151703
Includes 6 screws. You will need a size T20 Torx screwdriver.
$9.84
In Stock
Questions And Answers for SGI5916
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the SGI5916
[Viewing 9 of 9]Leaking
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The plastic clip on the roller broke
We let this go for a shameful amount of time before I decided I could probably fix it. The roller broke so you could only pull it out about halfway or it would come off the track. I looked up the part, and bought it. Actually bought two in case it happened again. When I arrived I looked at how it was put together on the other side and t
... Read more
hen just basically pushed it onto the rod and it was fixed. I am ashamed it took so long to do it. Never be afraid to try it yourself. It was a total of $10 shipped to fix it.
Read less
Parts Used:
-
Catherine from AMHERST, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
20 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring assembly on detergent and rinse aid dispenser broke so the sliding lid would not operate
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher
2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed.
3 ... Read more . unplug the wiring harness to the detergent/rinse aid dispenser
4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser.
5. the unit will pop out toward the inside of the dishwasher
6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in.
7. re-attach the wiring harness
8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job.
9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks.
10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
1. turn off electrical circuit breaker to the dishwasher
2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed.
3 ... Read more . unplug the wiring harness to the detergent/rinse aid dispenser
4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser.
5. the unit will pop out toward the inside of the dishwasher
6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in.
7. re-attach the wiring harness
8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job.
9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks.
10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
Read less
Parts Used:
-
Steven from SUWANEE, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
15 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not draining
I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .
Parts Used:
-
Bruce from MOUNT VERNON, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!