SEG196W-C Jenn-Air Range - Instructions

After accessing the switch and removing the wires(four wires as the rocker switch operates both fan and oven light) I attached the wires to the new switch. However , I was unable to mount the switch in place as I could not get the spring - clip type of fasteners to slip on.
Fortunately, there was space to drill a hole on each side of the switch and I used brass machine screws
and nuts to hold the switch. The round-head screw
tops show on top of the stove, but at least the new switch is in place and operating.

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

Took parts off from under the range, and replaced the motor. Then put the unit back under the stove and connected the vent.

Everything went fine. No trouble.

removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..

Removed top plate, disconnected old switch... Had to go to hardware store to get different push washers - the ones supplied with the part were too small. connected switch... tested connections and replaced top plate.

First Inserted 2x4x 36" length of wood behind the spring loaded door hinges to ease removing the oven door as I worked alone (this was recommended in a previous post and was essential when working alone, TY). Removed 2 retaining screws on the interior side of the door at the hinge locations. Slid the door up an off the hinges, moved door to a cloth pad protected work bench. Took the door and glass panels apart removing all the related screws, retaining clips; taking note of screws, retaining clip and panel locations for reassembly. Removed the insulation, removed the glass window pack, and removed of all rust fragments (dust) between the 2 glass window panels. The glass window pack metal molding retainer, on the oven interior side of the glass window had completely rusted away. Removed the existing oven door gasket. Cleaned the glass door window pack, and interior side of the oven door surface. Installed the new gasket, which fit very well. Tightened the loose door handle screws. Reassembled in reverse order all door components noted above, and replaced the door onto the hinges, fastened the 2 door hinge screws, removed the 2x4x36" wedge holding the hinges in the open position, and closed the door. Job complete. Thanks to previously posted directions as a good guide. Hope this helps as well.

Fortunate to have the replacement parts available.
Wish a replacement door window pack was available, as the double glass, metal edge seal is deteriorating, and the metal molding retainer that held the glass in place is completely rusted away on the oven side of the existing window pack. Plan to find heat resistant caulk to seal the glass in the door, in lieu of the metal molding glass retainer.

Much to my horror, what was described as a simple, 15-minute replacement, took 3 days! In order to replace the oven door gasket, I had to disassemble the entire door. Every photo I saw of the gasket showed it as a flexible part: gently pull out the old one and push in the new. What I received in my order had a frame. In order to replace it, I needed to unscrew the door parts. Unfortunately, I made a few rookie errors, primarily because I kept thinking the next screw would release the gasket frame. So I neglected to keep track of the screws I removed, and I didn’t take any photos!
I must have used half a roll of masking tape to keep parts together; I did not have 5 hands! When I released everything and nestled in the frame, I had even more trouble replacing all the screws I took out. The majority of holes did not line up. So I just did the best I could, put in as many screws as I could. But after three days of working, I finally finished. It all held together, and the door did what it was designed to do. Really a repair horror. And I am not an incompetent novice!

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.

lift out old filter, wash, put in new filter.

Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete

first removed the four screws that held the panel in place, tthen unscrewed the actual switch itself. I then pulled the wire, one at a time from the old switch and pluged the wire in to the new switch. upon completion I tested the oven selector switch and secured the switch in place, then replaced the panel. And I'm up and running again!

Disconnected power from the stove. First I removed the down draft vent cover on stove top, then the two screws that held the switch plate in place, then used a wood chisel to pry the switch housing retaining washers off. Removed the remains of the old switch, Installed new switch, attached wires, and reinstalled switch plate. Placed vent cover on stove top and reconnected power.

Remove old filter- put in new filter. EASY!!!!!!!!

Turned of electrical power. Loosen two screws that held the stove top part that held the switch. Disconnected the old switch by removing the two clamps that held it in place, made sure wires were connected correctly on the new switch and used the new clamps to attach the switch in place. Put everything back together and turned stove power back on. Everything worked as it should.