RTW4740YQ0 Roper Washer - Instructions

Tightened up the pulley as the video showed me that might be the issue.

I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.

Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.

I do not know much about washer repair and after watching how to replace the suspension rods I decided it was not as difficult as I thought. I replaced the suspension rods and springs and that fixed the problem. The price for parts was reasonable and I received my parts in 2 days.

Removed bolt holding top of agitator, removed top of agitator. Replaced parts. Reinstalled agitator. An old machine now works like a new model.

was really simple like others before me described. Removed cap to excess recessed bolt. Once that was out of the way pulled up gently on agitator and disassembled the agitator from base. Actually repair only took about 8 minutes. Working like new again and that keeps everybody happy! Thanks again.

popped off softener cap, easy. Pulled out clear plastic sealer, removed nut holding agitator in, pulled out agitator. Removed cam holder, new cam bearing etc in, reverse removal done, piece of cake.

I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machine worked fine right after I was done.The new part was identical the the old one,and the job was a snap.

Had no problem. The instructions included with the repair parts were very easy to follow and even specified the tools to use. I had it done, back on the washer and washing clothes in about a half an hour. The down side(no fault of the parts) was that the entire pump system went out on the second load and we wound up with a new Whirpool washer, since repairs were more than the machine was worth. Thanks Parts select for your help. I plan to search your net for more products. Fixing things from engines to microswitches is a hobby for me.

Please check the order was refused so I would not have to pay to ship back. The lady I spoke to on the phone said to do it this way. I have been TRYING to call for 2 weeks but no one is answering the phone due to CV19!!
The order is back at your warehouse. Please give me my refund!! Plus I have emailed your CS dept. numerous times with NO answer, only automated.

Followed the directions provided. Took less than 15 minutes and the washer works like new.

took off the soap dispenser, removed the agitator using a 7/16" socket with an extension. replaced the old top agitator dogs and retaining ring with new ones, re-installed top agitator on bottom, thenput whole assembly back shaft, dropped in bold and tightened. whole experience was fast and simple. the parts came fast and where a perfect fit.

Remove softener dispencer, use flat tip screw driver to remove agitator cap, there is a slot, insert flat tip screw driver and pry up, once removed you will see the damaged dogs or cogs, use 3/8 drive ratchet with 10 or 12 inch extention and if memory serves me correct a 9/16 socket, loosen bolt and remove top agitator, there is a thrust washer between bottom and top agitator, it comes in the kit, use a little grease preferrably water resistant grease on top of washer, replace top agitator then the plastic device that the cog are inserted into and tighten bolt, put agitator cover back on with a gentle slap of the palm and reinstall softener dispencer, you are done and cloths will agitate properly again, fairly easy job and washer agitator works like new, great kit, would reccomend.

Per your directions. Note that part has been updated from original. Looks like an improvement, adds tab to grab rod, but changes installation.

Watch video on the site and the insulation will be easy and take about 30 min.