Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RT18BKXKQ03 > Instructions

RT18BKXKQ03 Roper Refrigerator - Instructions

All installation instructions for RT18BKXKQ03 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RT18BKXKQ03
136-150 of 196
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker not making ice

  • Customer: judi from wallowa, OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
repair went well. Ice maker still not making ice. UGH

icemaker not working

  • Customer: shirley from wind gap, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed vidio instructions, took about 15 minutes. Fridge making great ice cubes again. Felt prouud of the repair I did being 70 years old and a female. Thank you

Old ice maker was leaking

  • Customer: Dennis from Rochester, MN
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Replace ice maker

Everything in fridge was freezing

  • Customer: James from Lawrenceville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replacing the thermostat was a very easy process. Couple of screws and then just matched how the existing one was installed.

Water fill tube was broke at the 90° in back of the frige

  • Customer: Douglas from Pahrump, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Water was already off. All I had to do was pull the fridge away from the wall, remove two screws that hold the fill tube onto the back of the frige, then remove the fill tube. Install the new fill tube, reinstall the two screws. Had to cut the water line straight and clean, slip on the new Compression nut and farrell and insert into the new fill tube, tighten-up, good-to-go.

Tray had rusted out, leaking!

  • Customer: Linda from Wilson, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Removed the screw from the old tray. Attached the new tray and return the screw using a wrench to assure the screw was torqued properly.

fill tube broken at elbow

  • Customer: Jack from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.

  • Customer: Burton from Pecatonica, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

Light switch which turns on the lights when the door opens went out

  • Customer: Dennis from Lawrenceville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

you have to turn it off and on to run.

  • Customer: chris from woodland hills, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

Warm freezer and fridge compressor clicking on and off

  • Customer: Christopher from Yorkville, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove rear panel with 1/4 nut driver. Pop plastic cover on compressor. Pry off relay and two wires and reinstall. Nice and easy and back to full function :)

Light in my refrigerator didn't work.

  • Customer: Joseph from Byron Center, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

freezer and refrigerator compartments not cold enough

  • Customer: Michael from Colorado Springs, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Ice maker replacement

  • Customer: Warren from Emerald Isle, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Hardest part is putting in the replacement ice maker. this is easily resolved if you have a 3x5 mirror. The mirror allows you to see where the screws are and place your 1/4 inch socket. The replacement part was identical to the original so did not need to replace wiring and other items included in the package received.

compressor not running

  • Customer: Doug from Lancaster, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
All Instructions for the RT18BKXKQ03
136-150 of 196