Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RF368LXMS0 > Instructions

RF368LXMS0 Whirlpool Range - Instructions

All installation instructions for RF368LXMS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RF368LXMS0
76-90 of 238
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broiler element not working

  • Customer: Normand from Lincoln, RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.

element went out on the stove

  • Customer: christopher from harrisburg, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's

Control panel on stove needed to be replaced

  • Customer: Sherry from Saint Cloud, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 12 people found this instruction helpful
Opened the back of the stove, unplugged the wires from the damaged panel, inserted the wires in the new panel, replaced the panel and back of stove. The plug-ins were located differently than the old panel, and two wires were identical - hope I plugged them in the right slots.

Broken Rear Drawer Glide

  • Customer: Ed from Maple Grove, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

The heating coil was no longer working.

  • Customer: Amanda from Midwest City, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

electrical short from oven light.

  • Customer: William H. from morehead city, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

Oven door was distroyed and dirty from previous owner

  • Customer: Alejandro from West Palm Beach, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 17 of 49 people found this instruction helpful
I dismounted the oven door following the graphic templates that this site has for that model. Then I replaced the gasquet (seal window), appliying an apoxic glue to hold it on place. Then I started to put it togueter, from the bottom to the top, first the lower trim, I screwed it back to the metal frame, then the left and right trims, it goes tied by pressing it to the sides, after that I installed the top and screwed it to the frame. It holded all toguether cery well. My oven looks like new now.

baking element non operational

  • Customer: GARY from JACKSON, WY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!

the screw came out of the oven door and the snapped the side molding in half

  • Customer: Djinnee from Jupiter, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 10 people found this instruction helpful
Well I had my oven door ducked taped together. I Am a 51 yr old female and I laid on the floor on my back to see if I could get the rest of the molding out without having to take off the entire oven door. I was able yo pop out the rest of the broken molding. I wasn't able to snap in the put it under the front of the oven door hold it together and screw in my new screw on the inside of the oven door. IT WORKED!! If I can do this so can you.

oven handle broke

  • Customer: Jim from CAMDENTON, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle

Element had burned out, and the drawer glides were broken .

  • Customer: Allen from ASHLAND, PA
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Replaced both .

Block had melted.R

  • Customer: Thomas H. from COCOA, FL
  • Difficulty: Very Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Removed old terminal block & replaced with new one. Very simple. Did NOT have to replace cover as stated you should. Shipping could have been a little faster. Will definetly try this site again.

broken glide

  • Customer: Andrew J from MASSAPEQUA, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
replaced glide with screwdriver. very easy

Oven Elementwas burnt into

  • Customer: Fred from APACHE JCT, AZ
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Watched the video and did as shown

I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.

  • Customer: Karen from Oklahoma City, OK
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.
All Instructions for the RF368LXMS0
76-90 of 238