RBD275PDQ8 Whirlpool Wall Oven - Instructions

I paid for an online advice service (Just answer)after failing to remove the hinges. The advice was not remotely helpful and I have asked for my deposit back.

Here are the steps:

Remove the door: Place the two tiny studs taken from the tongues of the new hinges in the same holes in the old door.
Holding the door just open, lift up and out to remove the door from the oven.

Lay the door on its inside surface, then remove 2 Phillips head screws from both the top and bottom edges of the door to release the front glass assembly. The hinges can now be seen.

Turn the door over and remove four Phillips heads screws to release the hinges, replace with new hinges.

Replace the two small studs in the hinge tongues and replace the door reversing the removal process. Remove and save the two studs (handy if you ever want to clean the glass on the inside)

The website and diagram of my oven helped me know exactly what was wrong and where to locate the problem. I simply removed the oven door and the trim, pulled the oven out of the wall. After removing the back panel I located the part and put in the new part. Then reversed the procedure.

Removed the door and laid it flat with the cracked glass facing up. applied duct tape to the broken glass to help hold it together. Removed the screws from the frame holding the glass. lifted the frame off,removed the broken glass and replaced it with the new piece. replaced the frame. and put the door back on the oven.

Turned off breaker to oven. Removed 2 screws, used pliers to remove 2 wires from old element, replaced with new part, connected wires to new element and screwed in 2 screws. Turned on breaker, then oven and new element heated. Very easy!

Replaced the lower heating element with a new part.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

removed door from oven using hinge locking pins supplied with oven when bought (two small screwdrivers might also work). Put door face down on a towel, removed two screw s on top and on bottom edge, removed back of door, then removed the two screws on eac side holding the old hinge springs. installed new hinge spings and replaced the door. no problems and used the opportunity to clean the door glass.

Removed door per manual instructions, then disassembled door components until I could remove the hinges. Nothing wrong with either one visually but, hoping the springs had become weak over time, I ordered replacements from PartSelect, knnowing I had a 30-day return window if my diagnosis was wromg.

It was right. Door now closes just fine.

Scarey> First thing you should do is cut off the electricity at the main breaker box. I dam near blowed myself up. It's 220Volt I found out after all hell blew up in my face. I was lucky and didn't get shocked.I shorted out the old broiler element.

So I made the job real easy I called a professional to come install the new broiler element.

I suggest you put a big red paper in each box that says turn off the power first. If your not sure how to do that call a pro.

My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.

1- TURN OFF POWER TO OVEN
2- REMOVE OVEN
3- REMOVE BACK PANEL SHROUDING
4- DISCONNECT POWER TO BLOWER
5- REMOVE BLOWER UNIT
5- REPLACE WITH NEW UNIT
6- RECONNECTED POWER
7- PUT OVEN BACK

Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going

removed control panel (4 screws) . replaced thermal fuse on back of control panel. very easy to fix for around $30

I simply plug all connections together , screwed in the decorative corners and I was done. I want to thank the company and tech for such a very quick turn around. I never thought I would get the control board back so fast. you received it on Tuesday and I got it back Thursday of the same week.thanks again.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.