RAX7245BW0 Roper Washer - Instructions

I just followed the steps on the video, I was surprised how fast I got the parts within 24 Hrs . Thanks

Remove the cover of the washer, pull out motor, pry out motor coupler, replace. May have to hammer with a rubber mallet to get it on. Replace motor and washer cover. We also replace the water pump. It wasn't broken, but since we had the washer torn apart, decided to replace it as well. There are lots of YouTube videos to help you out.

The top of the agitator pops out and leaves the fastener(a 17mm bolt) open at the bottom of a 6 inch or so opening in the top piece. That bolt comes out with a socket extension and the top comes off. Replacing the dogs is just a case of sliding a retainer ring down, removing the broken dog pieces and replacing with new dogs. Reverse the disassembly process to reassemble the unit. Now, it works great.

followed the video on the web site and repair was amazingly easy. I have two of these machines, and this same part went bad about 1 1/2 year ago, so this time i was ready for everything. Took everything apart, got rid of old broken part, replaced with new, and Bam, washer back up and running, less than 30 minutes, I am limited on space in my basement, so i didn't turn machine on its back, i did it in the upright position, just utilized some wood blocks to hold the motor during part change, and a hand spring clamp to hold pump and hoses out of my way after removing the clips that hold it on. It's not rocket science, if i can do it so can you. Good luck

Removed softener dispenser from agitator. Removed 1/2" bolt from inside agitator and removed top half of agitator. Removed cog assembly. Used screw driver to pry slip ring up 1/4 " to access directional cogs. Replaced cogs, pushed slip ring back into place. Reassembled agitator in reverse order of disassembly.

First I tipped the washer forward and placed a plastic milk crate under the rear of the washer to support it . Then tipping the washer back. I placed two car jack stands near the front to support and level the machine. Now I had enough room to look under it to see where it was leaking. Right away I could see a drip coming from the pump in the front of the washer. I removed the two water hoses. Then with a screwdriver popped a clip on the top of the pump and one on the bottom. The pump slid easily off . Slide the new pump on and reverse the process

Followed written instructions after viewing repair video. Would have been helpful to know how far onto shaft each drive piece needed to be placed. I should have noted old piece placement, though if this was noted in instructions it would have been reassuring to know what is the proper placement. I also placed machine on its back to align the motor and transmission after new parts were installed on each.

Removed agitator cap with flat head screwdriver, then removed inner seal cap and removed worn cogs. Installed new cogs and replaced o-ring seal on cap installed new by and was good to go in under 15 minutes.

Ordered the repair kit and when it arrived a few days later we removed the cylinder for the fabric softener and lifted the screen cap off, used a nut driver to remove the top part of the agitator and then simply removed the old worn parts and replaced with the news. Easy peasy! ;)

We started to get water hammer in the pipes when ever the washer was set to cold? Looked it up here and figured the inlet was about to go out, ordered the part, 2 days later, brand new washer, no more problems. Local repair would have cost us at least $100.00, part was $25.00 shipped, videos are awesome tools, PartsSelect Rules!!!

I looked at the fine parts blow-up drawing available on internet. It was immediately clear the teeth had worn smooth on the cogs, and replacing them would fix the problem. I placed the order for the three parts sets I felt would be useful, and the most amazing thing happened, The parts arrived the next day, they were all in the package they all fit, and I was washing clothes within and hour. The information on line was understandable and accurate and the speed of delivery was outstanding.

I researched the troubleshooting on PartSelect.com and determined the clutch was going out on my direct drive Whirlpool washer. I ordered the part, found the instructional video that actually had my exact washer being worked on, I followed all of the steps of replacing the clutch and in a snap, my washer was spinning. I've worked in apartment maintenance for years and PartsSelect.com has always been my only resource for appliance parts and repairs. The prices are great (I've compared most parts websites and 8 times out of 10, partsselect.com is cheapest), the shipping is extremely fast and the parts are alway right. Great site!!!!

Follow the video to remove the cabinet. Did NOT have to lay the unit on its back in order to replace all 5 springs. These may be easily replaced with the washer standing upright. The back Suspension Spring was removed by using the access hole in the back of the washer to remove the screw holding the back spring bracket in place. Reassembled the cabinet per the video. Except for moving the washer around, this was an extremely easy repair. To facilitate moving the washer - use Moving PADS placed under the 4 feet of the washer.

The repair was easy and the video tutorial was great. That was the easy part. I also had to replace the drain pan and getting it in and out of the pan is no easy task. Plus when you have not moved the washer in 10 years there is some cleaning to do. I would not hesitate to do it myself again. It cost me $20 and some sweat equity.

Removed the fabric softner dispenser, used a 7/16 socket with ratchet to remove the bolt, pulled up on the Lower Agitator. Placed on floor, put foot on each side pulled up on the Upper Agitator tossed away. Cleaned the lower agitator at top reached in with a pair pliers removed the two little tits. Replaced the parts as per instructions with parts. Wished they had included the grease as part of the kit, i just used some white grease it reples water and good for friction. My kit did not have a new bolt in it.