Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RAS7233JQ0 > Instructions

RAS7233JQ0 Roper Washer - Instructions

All installation instructions for RAS7233JQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAS7233JQ0
1,081-1,095 of 1,462
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace leaking water pump

  • Customer: Dewey from DeRuyter, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair video was very helpful and exactly right. The most difficult task was removing the old pump. It had apparently seeping between the motor shaft and the pump coupler for some time and had rusted the pump to the motor shaft. I had to aggressively grip the pump housing with the channel lock pliers and wrench it back and forth to break it loose. I took a file to remove the rust build up from the motor shaft before installing the new pump. Washer works fine.

Washing machine shook violently during spin cycle

  • Customer: brian from las vegas, NV
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Luckily enough the washer shown in the demonstration is my exact model, which eliminated any variables I may have come across. The repair was relatively easy and probably could of been done in less time but I took every step slowly to avoid breaking something or leaving something unattached. For the money and time spent on this repair I would certainly recommend this for anyone with a similar issue. After taking the machine completely apart, i found that the suspension pads were still properly functioning. Since i had already purchased them with the tub wear pads, I changed them anyway. The trickiest part for me was pulling the outer tub out because the shaft on my unit was very rusted had a considerable amount of buildup on it. During this step I was very careful to remove all the build up because there is a single rubber seal between the center opening of the tub and the motor shaft. After I made sure the shaft was completely smooth and there were no protrusions I gently rocked the tub back and forth while applying pressure from the underside of the tub, all the while making sure that the seal didn't fold in on itself or stretch in any direction. Other than that, the repair went very quickly and easily . The spanner wrench is a must !!! I actually found it on amazon for about 6 dollars and I'm positive I will find another use for it somewhere down the road. I owe a big thank you to Steve. (the guy in the video) and everyone else from parts select for making laundry day in my house tolerable again !!!

Had issues with removing the inner tub

  • Customer: Bruce from Yankton, SD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!

Motor Drive Coupling

  • Customer: Kenneth from Stoughton, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and that was a great help. I just entered my model number and selected the symptom. 61% of the time the drive coupling is the problem and it was. Ordered the part and got it the next day.

The Shaft On The Direct Drive Was Worn

  • Customer: ALLEN from Newton, KS
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Removed the control panel and the cabanit. Then removed the adjutatior . Removed the motor and gear box slid the old shaft out and put the new one in put back together. Took about one hour .

Water was not being drained from my washer

  • Customer: Mitchell from Rushville, IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After figuring out the shell was not gonna come apart easily, as some videos show for Whirpool, Kenmore.., to gain access to the water pump, I decided to try a trick I'd heard of before and try to get to it from the bottom. Since most washing machines have their water pumps in the front, I pulled it out enough to be able to lean it back against the wall and look underneath. Be very sure you have unplugged the machine from the outlet! Also be sure to support it from falling forward. The hoses and pump were easily accessible from this position.Using the pliers to remove the hose clamps, I could wiggle the hoses off easily. Be prepared for some water to run out, because there will be some in there. After removing the hoses, the clips holding the water pump on were easily removed with my fingers, you might need a screwdriver to loosen the clips. With the clips pulled back, or removed if you turn them 90 degrees the pump should pull off the shaft of the motor easily. A gentle tapping will usually loosen any stuck pump.Once the old pump is removed, line up the shaft of the motor and pump's sleeve with flat sides matching and it should slide on easily. Do not force it, it should slide on easily if lined up properly. Replace the clips holding the pump to the motor. Reconnect the hoses, slide the clamps back into place with the pliers, and you should be ready to Rock-n-Roll. Lower the machine, and slide it back into place. Hope this helps all of those that choose to repair their own Crosley washing machine with a new water pump.

Intermittently the spin cycle would not empty the tub fully

  • Customer: Robert from York, PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First off, let me say two things, this was my very first washer repair and the installation video was excellent.

Few things though ..... The first thing I noticed was the old parts I removed did not look that bad to me. I was starting to wonder if I was wasting my time. However, its apart now I'll continue on. I had a hard time properly seating the new couplings on either end correctly. They were VERY snug. What I ended up doing was getting a 20mm deep socket that fit perfectly onto the coupling and with a hammer gently, (and I underline gently) tapped the new parts into place. That fixed that problem. I also had some minor difficulty putting the cabinet back together, but nothing earth shattering. The cabinet fits on top of the frame, not under. And lastly, the small clips that hold the console on were not very reusable afterwards so I'll need to order a new set of them sometime.

All-in-all it was a fun repair that didn't take me too long and I saved quite a bit. I definitely would do it again if necessary. I've done about 5 loads of laundry since and everything seems to be working great so far.

- Bob

Lid Switch mounting broke

  • Customer: HOWARD from Seal Beach, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video was very helpful and the written comments helped. The longest time was spent in reassmbling the front cover/top assembly onto the base.

Washer tub leans to one side. ( Not centered.)

  • Customer: Edgar Seabrooks from Philadelphia, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the washer and removed the two screws from the control panel. Raised the control panel and disconnected the wire connector that connected to the top.Then removed the two spring clips that hold the cabinet to the back of the washer. removed the cabinet from the washer that exposed the frame of the washer. I then replaced the broken spring by pushing the tub of the washer as far as it would go and replaced the suspension spring. Then i reinstalled the cabinet and control panel. Everything worked okay. ood as new.

The machine won't drain, won't continue the cicle.

  • Customer: Ada from Bourbonnais, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We just followed the video, it was very helpful. We are very pleased with the results. Ordering, receiving the part and fixing the problem was a learning experience. This is a realiable site. Thank you so much.

Washer would not spin. Coupler was the problem.

  • Customer: Joey from Murrieta, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The video they provide was very easy to follow. The only difference from mines and the video they provided was the top portion. Mines was held by two Phillips screws on the switch housing. The top pulls forward. Everything else went accordingly. Take off switch plugs, take off washer cover, unplug the vacuum line, replace coupler and reinstall. Only thing that took up time was getting water off the floor when I pulled the vacuum line. Use a bucket or do it outside.

Pumps but won't spin, leaks, top of agitator doesn't move

  • Customer: Kenneth from Talbott, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My repair was successful but was not as easy as some have reported. I needed to replace the coupler, but when I tried to remove the pump from the motor, the shaft was rusted and wouldn't budge. I pried and wiggled and used WD-40 to no avail. I ended up taking off the motor and pump as a unit. After replacing the coupler and reassembling the washer, the water pump leaked, probably as a result of all of the prying. To get the water pump off, I had to cut it into pieces, using a hack saw. Even when I got down to the end, I had to peel pieces of plastic off of the rusted shaft. I then had to file and sand the shaft to get it so that it would fit into the new pump. After putting the washer together again and running it through its cycles, I noticed that the top half of the agitator was not turning. I then ordered and installed the agitator repair kit. Through all of this, my orders were all correct and arrived in amazingly fast times. The videos were all very helpful. Even though it was a trial a times, I still saved a pile of money.

The washer would intermittently not spin for the last 5 months. Water would drain on the spin cycle but not spin. Read several websites on the problem but only one hit it exactly.

  • Customer: David from Wilmington, DE
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
First watched YouTube video "Kenmore/Whirlpool washer not spinning", excellent video .Disconnected water hoses and drain hose. Unplugged the washer from the outlet. Removed the agitator from the washer tub then tipped the washer backwards resting on a secure block of wood for support not fully on the floor. Removed under insulation, removed both water pump hoses. Have towels ready when hoses are removed, there is still water in the hoses. Removed the water pump, disconnected the electrical connector from the pump motor, removed the bolts from the motor that attached the motor clips, removed the motor clips from the bracket and removed the motor assembly. Video shows motor, bracket and gearbox removed as one unit. Very heavy. Remember motor position on the bracket for reassembly, I used yellow marker. Removed the bracket the mounts the motor. Removed the bolts for the gearbox and began to lower the gearbox. The agitator shaft on the gearbox is pretty long so I had to tilt the washer some more to remove. After the gear box was removed I could now see the spin clutch, which according to the video was definitely bad. PartSelect had the correct part, reasonably priced. Ordered normal FedEx delivery, part arrived in 2 business days. Instructions came with the part for very easy installation. Installed the new clutch and reassembled the washer. Before reconnecting the washer hoses and drain, I plugged in the washer, manually placed timer on spin, washer spun, could not see spin but felt washer in spin cycle. Reattached water and drain hoses. Filled washer empty with cold water and placed timer again in spin cycle. Water drained, no leaks under washer or from hoses, spin cycle good. Repair done, works great.

noise caused b y broken coupler between motor and transmission during "spin" and not spinning

  • Customer: John P from Brazil, IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed motor and broken coupler... installed new coupler and replaced motor. also removed pump to inspect for sock, etc. that that might have caused coupler to break.. ADVICE: Look for how-to video on YouTube first. Remove outer cabinet according to video by first removing the top control panel and then remove the outer cabinet which exposes the motor and pump. This way you will not have to tip machine up/back and work under it. This repair is made easily by first removing the outer cabinet.

Washer would not spin

  • Customer: Mark from McCall, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I followed the instructions from a YouTube video, just do a Google search for the make, model, and what the problem is and several videos will come up to pick from. Everything went just as described in the video, took about 10-min to take the motor out, a couple of minutes to replace the broken motor coupling, and another 10-min to put it back together - slick.
All Instructions for the RAS7233JQ0
1,081-1,095 of 1,462