Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PLES389DCC > Instructions

PLES389DCC Frigidaire Range - Instructions

All installation instructions for PLES389DCC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PLES389DCC
31-45 of 89
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven wouldn't work

  • Customer: david from olney, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
It's kind of embarrassing!
As the breaker was being thrown to turn the current off, I discovered that the breaker box was burn up at the breakers.
Short story but I got'er done! The problem now is there is something still wrong with teh oven!
I think I see a new one in the future!
Thank you very much for the very prompt delivery.
My purchase has been without a flaw.
I have already sent the part back for a refund.
It cost me something like $13 for this experience for freight.
I will remember you with my next need.

A friend shot out the front glass panel of my oven door with a BB gun!!

  • Customer: Fritz R. from Carnelian Bay, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 9 people found this instruction helpful
Just "locked" the hinges, pulled the door off. Removed the broken glass for the door. Switched the handle from the old door to the new one. thPut it back on e hinges.....viola!! new oven door glass!

Replcement of inner door glass which had shattered

  • Customer: Michael A from Fairhaven, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 7 people found this instruction helpful
Removed the door from the range, disassembled the door, removed all broken glass fragments, installed the new glass, reassembled the door and reinstalled the door into the range. Straightforward and easy. Keep track of which screws go where and it is a breeze.

bottom oven element not heating

  • Customer: dempsey from eastland, TX
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 115 of 366 people found this instruction helpful
replaced bottom oven element, did not fix the problem. replaced the thermostate and the terminal block and that did not fix the problem. parts select what is next?

Heating element burned out

  • Customer: Jack from Hedgesville, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took screws loose, unplugged old one plugged in new one put screws back

Cracked Oven Glass

  • Customer: charlene from princeton, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair went relatively easy. I even cleaned all the layers of parts when they were removed from the glass panel. I have to thank the excellent customer service and super fast delivery. Overall a quite easy task and $$ saving as well!

Oven would not heat after running self clean

  • Customer: Michael from Owasso, OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

Control will not work - only clock blinks

  • Customer: Sue from Lampasas, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Improper temperature when baking.

  • Customer: Lorenza from Rowlesburg, WV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

The warning light for the warmer was stuck "on"

  • Customer: Linda from Pleasant Mount, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Turned off electric at the main box. Removed glass top. Used a razor knife to pry the connections loose so that the new connections could be slid in. Problem was that the element ordered looked entirely different then the original one. Even the hookup was different. But once the connections were made, the ceramic top placed on top, and the electric restored everything seemed okay. The warmer works and when it heats up the warning light turns on. When the warmer cools the warning light goes off as it should.

Cracked inner door glass

  • Customer: Franklyn from Jupiter, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Started with three screws on outer edge of door, which separated inner and outer door parts exposing the first set of screws on first piece of glass. There are four panes including inner and outer with two between. Keep track of the screws, be careful removing and replacing glass panes (i put mat down to rest glass on)and with nothing more than a screwdriver and windex to remove fingerprints etc from replaced glass, it was a breeze. Good luck! - FK, Bahamas

Error Code F1

  • Customer: Jon from Little Silver, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first

"hot" indicator light on glass cook top burned out

  • Customer: Kathleen from Middlebury, VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

Door gasket was worn, stained and needed replaced

  • Customer: BETSY from HENDERSONVILLE, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!

Improper oven heating.

  • Customer: Lorenza from Rowlesburg, WV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!
All Instructions for the PLES389DCC
31-45 of 89