PLEB30M9ECD Frigidaire Microwave Oven Combo - Instructions

Unsrewed side plates and removed old hinge and replaced with new. Recomend doing both left and right hinges or door will not close square.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

watched a U-Tube video on this subject.....worked like aa charm!!

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Replaced both springs. Follow instructions in owners manual on removing door. Spring assembly resides in door. Remove screws holding spring assembly in place, then the remaining screws holding the inside of door in place. Raising the side, slide out old spring then slide in the new one - do the same on the opposite side. Replace all the screws - starting with those that hold the spring assembly making sure the latches are straight. Put the door back on making sure to lock "spring locks" detailed in owners manual

Easy fix for my microwave. The cover just slips out, no tools needed.The best part about this fix was dealing with PartSelect. I recieved my part in less than 3 days but it was damaged. PartSelect overnighted a repacement and I am back in business.

pulled door off took door apart replaced hinge

Husband made install in very short time. Nice to have them back in operation.

I removed the element, plugged in the new one and that has corrected the uneven oven temperature.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Found a YouTube video similar to the required repair. Took door off, disassembled the door, replaced the right hinge-spring assy, reassembled. Worked great. High quality replacement part from Part Select that was made in the USA.

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

I noticed that the scorched and slightly melted plastic was above a little piece of what looked like cardboard, so I did a Google search for "flames in microwave" or something similar and found a link to a DIY repair site that mentioned a tear in the waveguide cover causing that problem. I ordered a replacement from PartSelect, received it in near-new condition, and replaced the old one with the new one in 5 seconds. I then called PartSelect to let them know that the new part had a couple of "wrinkles" in it that I was concerned might cause a problem down the line but that it seemed to be working OK for now. The nice person in customer service told me that I could use the part for the full year of the warranty and return it if a problem arose. I'm very satisfied with the experience!