Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PHSC39EGSS0 > Instructions

PHSC39EGSS0 Frigidaire Refrigerator - Instructions

All installation instructions for PHSC39EGSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PHSC39EGSS0
391-405 of 552
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace a broken water dispenser Actuator

  • Customer: Douglas from Topeka, KS
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the drip plate out and removed the 3 screws that hold the face of the ice & water Actuators. Removed the 2 upper screws that hold the frame work of the water Actuator & pulled the water supply hose out of the frame of the water. Actuator. Worked on the part that holds the Actuator on the kitchen table. Two screws hold the plastic water Actuator in place so removed them & unplugged the broken Actuator & started reversing the process to put the new Actuator in. The biggest challenge was getting the water hose back through the hole without tearing more parts out in order to get enough room to put the water hose through the hole it rest in. I decided to run a screw the same size as the inside of the hose and put a little butter around the hole , run the screw through the backside of the hole into the inside of the hole then begin pulling the hose through the hole as I put the frame panel back in place. If there was more slack in the hose it would of been easier. Bottom line it worked & saved me money.

Drawer support broke.

  • Customer: nancy from Bellingham, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I was worried that the support was a permanent fixture in the refrigerator wall. But I pried it out and replaced it with the new part. Holes were exactly the same size so the new part easily replaced the old one.

support clips broken for 2 bins

  • Customer: Thurlowe from Tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Purchase was easy. Delivery was quick. Install videos was accurate. Made it eady to as DI project. Safe place for purchase and support. Saved on cost of professional visit.

Water dispenser/ice maker not working

  • Customer: Sierra from Seattle, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed previous directions, and would recommend them! Briefly, I removed the plastic covers for the water filter, water tubes, temperature control switches to allow removal using a screwdriver and a nutdriver(I think)to remove the hexagonal screws. I also removed the water filter before beginning. I pressed the blue thingies in the back towards the base to remove the water supply lines. It was a bit tricky, and took the bulk of the repair time, but they came lose once enough pressure was applied. I took out the old filter base, put in the new one, attached the water lines, and put back all the covers. Everything comes apart very easily, and went back together very easily. A simple repair that had us back in ice and filtered water within an hour!

Ice dispenser broke

  • Customer: John from Franklin, LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged refrigerator and turned off the water supply. Removed dispenser unit and replace broken part.

ice maker inlet leaking

  • Customer: kevin from east haven, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed backing to refrig unscrewed 2 screws from bracket pulled unit out unhooked hoses and elec plug's / putting in new just reversed the instalation

Water not pouring consistently.

  • Customer: Karolina from Naperville, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced the water filter ( two minutes). Water not only pours evenly, but tastes great, I was so worried about finding the correct filter for the fridge. It took minutes to order online and the correct part for my model arrived. Extremely happy with my purchase.

crisper shelf support broken

  • Customer: James R from East Stroudsburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove crisper and shelf. Use a small punch and hammer to gently push the tightening pin through to the wall of refrigerator, keep in mind you'll need to remove this piece with small needle nose pliers before installing new part. Set new part in place and lightly tap the pin in until flush. Install crisper and enjoy the rest of your day.

Broken cover support

  • Customer: John from Frederick, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Remove cover, puch old pin into hole. Remove old support. Set new support in & drive pin in flush. Replace cover.

Leaking water

  • Customer: Omar from Vestal, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My part had threaded fittings. The part that I received had snap fittings. Once I realized that that snap fittings worked with the bare tubing and not any special tip endings, I simply cut off the ends of my tubing that mated with the threaded fittings. I then had bare tubing that snapped into the snap fittings. Two minutes later, the part was in place and the job was done. Problem solved.

Broken Actuator lever

  • Customer: David from Newport, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Google'd "Replacing the Water Actuator Frigidaire" on YouTube and they have a directional video on how to fix one, not the exact one we have, but very close. I'm very handy so this was very easy for me, took 20 minutes.

my in-laws can dispenser broke

  • Customer: R. from AUBURN HILLS, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
it was an easy fix after I finally got the right part from the right people. only took me about 5 minutes to figure out how it went back in. thank you partselect.

Plastic water dispenser broke on fridge

  • Customer: Robin from Castro Valley, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched a video on YouTube of the repair, followed the instructions and it was a breeze. Repaired dispenser for the cost of the part.

Ice maker doesn't make ice - or makes too much

  • Customer: Tonna from Carpentersville, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
For many years now, we have dealt with this ridiculous ice maker. Either it overflowed with ice and poured water down the back of the freezer - or it wouldn't eject ice at all. I constantly had to intervene. A repair man rigged a wire device to extend the arm to help it detect if the tray was full - that helped a little bit. Finally it just quit making ice. I read all of the positive reviews here and decided I would give the new replacement a shot. And wouldn't you know - it worked! Easy 2 minute install and our ice bin is now full all the time. And man is this one so much quieter than the old one! Only con - the original tray that fits over the maker and bin doesn't align with the new icemaker. If its pushed all the way in, the arm can't rise high enough to eject the ice - so we have to keep it pulled out as far as it can go and still allow the door to close. A little wonky - but hey, we have ice without intervention! Why did I not do this years ago?

Dispenser Broke

  • Customer: CRAIG from TEXAS CITY, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair went well. Fairly easy. The water line was dificult to get back in the dispenser hole once removed. You do need to unplug the appliance to prevent being shocked by the circut board and to keep the water dispenser from operating when instaling the new peice.
All Instructions for the PHSC39EGSS0
391-405 of 552