PHS68EJSB0 Frigidaire Refrigerator - Instructions

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

Remove both crisper pans and covers. Discard old frames and re-use glasses. Use two screw drivers to gently pry out broken supports. Top broken off smooth on one support. Unable to grasp with pliers to pull out. I drilled a small hole in the center of the large expansion pin. I screwed in a small sheet metal screw. Used side cutter pliers to grasp screw and gently rock back and forth to remove center of large pin. Plucked out broken pieces with needle nosed pliers. Gently tap in expansion pins to install new supports. The rest is simple re-assembly using new parts. "Nothing to it but to do it."

Just snapped into place. Very easy.

The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.

It was very easy. I attached to the socket.

Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.

Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.

Just pushed the button along side the filter and it popped out in my hand. I unpacked the new filter module and inserted it. It was necessary to run water through the dispenser for a couple of minutes to purge the air and clear the lines. The modular filter assembly is more expenseve than some but the ease of replacement makes the cost a good value.

Removed (unsnapped) plastic cover from back of refrigerator ( inside freezer compartment), determined that the fan was not turning, removed 4 screws from the aluminum back plate in freezer and tilted it down. Removed 2 screws with a nut driver, this allowed the fan to be removed, unpluged fan motor from the bace of the freezer and removed fan. Installed new motor and spent $38.00 to repair the refrigerator that would have cost me severial hundred dollars to replace. Thanks for the help

First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.

The Sears repairman wanted to charge me $359 to repair. I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.

I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.

Snap out fan cover, remove four 1/4" screws, remove back cover, remove defective fan motor, remove fan blade, install new motor and blade, strip wires and hook up with wire nuts, reinstall back cover, snap in fan cover, and plug in fridge.

The electronic board died. Found the part and order it. It arrived in two days. I put it in in 15 minutes and fixed a 2000 dollar ref. I am one happy camper.
Bob

Just opened the filter storage and popped out the old one and put in the new one. Ran the system for three minutes according to directions and it worked fine.