Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PFS22SISBSS > Instructions

PFS22SISBSS General Electric Refrigerator - Instructions

All installation instructions for PFS22SISBSS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PFS22SISBSS
286-300 of 471
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

freezer warm, clicking noise, refrigerator warm

  • Customer: eric from Burlington, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the back cover about 7 screws then removed the fan shroud the top part folds down and then slide to the right and angle down. remove to two screws holding the motor in spread apart the plastic housing to remove the wire connector. unclip connector .

No problems.

  • Customer: Patricia from Norwood, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.

Control board fried when condenser fan stopped working

  • Customer: Scott from Golden, CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed cover, disconnected all the connectors, removed the old board, installed the new one and put all the connections back in place.

Food Freezing In The Crisper Drawers

  • Customer: Steven from Lampe, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Watched the how-to video and then followed the steps. After unplugging the refrigerator I removed the main control board cover, disconnected the wiring plugs and the removed the old control board. Installed the new main control board, reconnected all the wiring plugs and re-installed the cover. Refrigerator has been working great since the repair.

The Ice Maker stopped making Ice because the arm over the ice bucket which turned turned on the icemaker was broken

  • Customer: Mitchell from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!

Icemaker stopped making ice

  • Customer: James from North Billerica, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

Refrigerator would stop. Could hear clicking from the computer board. Could spin fan and it would start again. Ice dispenser stopped working. If you hit the dispenser the motor would stop and start clicking again

  • Customer: Ken from Stockton, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Pulled the refidgerator from the wall. Unplugged the refrigerator. Took cover off the back where the mother board was. Took a picture of all wiring with my phone just to be safe. Unplugged all wires. Used pliars to release the four white plastic pins to remove the board. Reinstalled the board in reverse order. Put cover back on the back. Plugged in the refrigerator to check if it worked. It came right on and now my water and ice dispenser all work like they should. Very easy to do! These guys make it easy! Bottom line! It'll save you money!

fridge was not cooling,ice maker not working. and making a clicking sound

  • Customer: jonathon e from cincinnati, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1)unplug the refrigerator from the wall 2)simply opened up the back panel by removing the screws with a nutdriver. 3)disconnected all the prong connections one at a time. 4)take new control board and reattach all prongs and green ground wire.5)reinstall rear panel 6)plug in refrigerator.

Noisey, Ice auger motor not working, water dispenser worked poorly

  • Customer: Jose from Henderson, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I follow the instructions on your video to change the mother board and the Ice auger motor. The repair was as easy as the video and just as simple....Thank you.

The refrigerator was not cooling

  • Customer: James from Pearland, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I received the new board 6 days after making order. Very simple task. Unplug refrigerator. Removed 3 screws holding cover on back panel. Disconnected 4 wiring harness/connectors. Using needle nose pliers, I compressed the 4 plastic tabs that hold the board to the frame. I did one tab at a time and as I compressed the tab, I pulled the board away from the tab. I connected the harness/connectors to the new board before mounting on tabs. The new board had been updated and had 6 areas for connectors, just match the correct connectors to plugs, they only fit one way. Install cover plate, but remember to connect the new ground wire (green) to one of the cover mounting screws. Plug in unit and and give atleast 12 hours prior to adjusting the tempature controls.

freezer would not defrost or maintain temperature

  • Customer: Jason Mcgee from Catawissa, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

No Ice...

  • Customer: Eduardo from Arlington, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Super easy, had my 15 year old do it (with my supervision).
Followed very clear Instructions that come with the replacement...
But, he could not get to the plug location until he removed 4 screws holding the motor assembly that spins the ice in the drawer and moved it out of the way...
Followed the rest of the instructions...
Works like a charm.

Water & Ice Dispenser Quit, Then Fridge Intermittant

  • Customer: DENNIS from ESCALON, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Pop in new board

ice maker would not work

  • Customer: Wickham from Bedford, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed the instructions that came with the part

No ice cubes & just ice shells

  • Customer: William from Collingdale, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
No need to shut off the water supply. A pair of pliers was required to remove the old filter, and the new one went in with just a quarter turn. It locked in place with no water drips. Less than 5 minutes to install.
All Instructions for the PFS22SISBSS
286-300 of 471