PDW7880J10SS General Electric Dishwasher - Instructions

Once upon a kitchen dreary.
Washing dishes made me weary.
All the dishes would not clean.
Gunk clogged up my filter screen.
The lower spray arm stuck and rattled.
With flying muck my dishes battled.
The muck had won and I had lost.
The repairman said it would really cost.
And so I did a google search.
Partselect got me out of a lurch.
Correct parts were easy to choose
and service so quick I couldn't lose.
I took off the old parts and tightened the new
No tools were needed my fingers flew.
And now my dishes come out clean
I feel competent and frugal, you know what I mean?

I noticed the circulation pump was not operating. If I turned the motor with a screw driver it would start running. I replaced the pump and now the dishwasher works like new. Very easy to replace the pump but you will have to pull out the dishwasher and turn on its back. I was able to confirm the circulation pump was the problem by observing the motor not running when it should but it would run once I turned the inside motor parts(be careful!). I also had to replace the center sprayer which again was very easy.

Just put axle and wheel together and popped them on. Thank you. I know you saved me a bundle.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

We pulled the dishwasher out completely, drained water that was in the dishwasher. Tilted the dishwasher and the part we needed to replace (Pump Drain Assembly) was in clear view. We used a screwdriver to take out a few screws and replaced the Pump Drain Assembly with the new one. Put the dishwasher back in and proceeded to wash dishes in the now fixed dishwasher. The part was very easy to change out.

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

pulled the racks out, replaced the broken parts....easy job

The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy.

Bottom rack - slide the old one out, slide the new one in. The rack came came with the wheels, so I didn't use the replacement ones.
Top rack - remove the rail end caps - they will likely break so order new ones. Slide the rack out. Remove the rotating spray arm and then remove all the brackets. I was able to re-use the old brackets and didn't need the replacements. Install the old brackets on the new rack, install the spray arm, and slide the new rack back into the rails. The new top rack also came with wheels installed, so I didn't use the replacement ones. Once the rack is back in the rails, install new rail end caps. Put them in sideways and facing into the washer. Straighten the caps and turn them into place. Be careful with the rail caps - they break easy and are expensive. Make sure they hold the top rack in place, and that's it.

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled

My dishwasher was doing a terrible job of cleaning. It was leaving food on dishes, and wasn't dissolving all the detergent. I replaced all the spray arms and the filter, as they seemed clogged, and god knows how old. It's a super easy repair, and the dishwasher now works as if it were brand new.

I removed the screws on the inside of the door assembly, which allows the inside of the door to seperate from the outside. The escuchen (control panel) was easy to remove - the handle actuator is inside the control panel. The handle assembly was easy to take apart and re-assemble with the new handle and spring. I then inserted the control panel back into the outside door and reattached all of the screws with a power drill. This was a repair that a GE-authorized service tech told me was going to be over $540 - he claimed the control panel and door handle/actuator was a single assembly. In the end this repair cost me $14 in parts and 15 minutes of time. I complained to GE Consumer Affairs and they rebated the tech house call back to me in 5 business days.

This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!