Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PAV2300AWW > Instructions

PAV2300AWW Maytag Washer - Instructions

All installation instructions for PAV2300AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PAV2300AWW
451-465 of 627
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Pump was leaking water on the bottom

  • Customer: Yevgeniy from Monroe, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I did it just like a video was showing. This was really good instructional video.

Bad Water pump

  • Customer: Robert from bridgeton, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Tilt washer back and pop belt on bottom of washer. Use putty knife to open top of washer 2 clips 2 inches in from both sides. Use racket to open and remove front panel of washer. use racket to remove 3 screws that hold pump to base of washer. pliers to remove clamps for intake and output hoses. use small bucket to catch water in hoses and pump. Replace pump unit, put screws in, put pump clamps on, put front panel back on , snap down top of unit, put belt back on pulleys and your done.

Washing machine made a strange loud noise and then would not drain.

  • Customer: Dermot from Coral Springs, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
The video on PartSelect.com regarding replacing the washer machines drain pump with pulley was extremely helpful. By following the simple instructions as shown in the video, I was successful in replacing my washing machines pump in less than an hour, and saved myself the labor costs a repairman would have charged me for a really simple and easy repair job. I was also extremely happy and impressed with PartSelect.com. The price I paid for the part was very competitive and arrived within 3 days. I was very glad to see the pump and pulley assembly was a Whirlpool factory certified part and not a knock-off or reconditioned part.

loud metal on metal sound during spin cycle

  • Customer: Shane from Mobile, AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed write ups on this web site and the job was straight forward. As far as the washer brake rotor I did not need to replace it. After removing the six screws that cover the assembly I noticed some rust and dirt so cleaned it with degreaser and reassembled it. I have no loud screeching sounds when the spin cycle comes to an end. As always PartSelect did a great job getting the correct parts to me with in a few days, thanks.

Noisy during wash cycle and spin

  • Customer: Phil from Winfield, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removing and replacing the pump was a very easy process. Once the belt was removed on the bottom of the machine, I removed the back plate to gain access to the pump. Three screws and a couple of clamps holding the hoses on the pump. There was a little more water in the pump during removal than anticipated. Other than that, it was an easy fix.

water won't leave the washer, make laud noise and burning smell

  • Customer: Joshua from Naperville, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
remove the cable under the washer, open the back small opening/access panel, unplug two hoses, remove and replace the pump, put everything back including the cable under the washer. then test and it washes like new and quiet. Installation video is very helpful.

Washer made squealing and grinding noises at the end of a wash cycle

  • Customer: Leonard from Hot Springs Village, AR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I followed the very useful videos for replacing the water pump and drive belt. My machine has the water pump located in the back (different than the video) so removing the front of the washer was not necessary. However, by doing so, I noticed some interior rust from bleach-tray spills which I easily fixed with a wire brush and some spray paint. The pump was easily removed by loosening 3 bolts (per the video) but through an access plate in the back. The only surprise was that there was considerable water in the pump hoses and I needed a bigger catch tray to collect the water than I expected.

Hinges for the lid were broken

  • Customer: David from Chandler, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair went smoothly with no issues or problems. The video link sent with the receipt made all the difference in the world. I watched the video on my iPad as I was doing the repair. Also locating the parts I needed on the part select website could not have been simpler.

Lid on washmachine was loose. Found that one of the plastic hinge pins had broken.

  • Customer: Larry from Woodbury, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered two new hinge pins as well as hinges. (Did not want to have to deal with it again so chose a full change out.) Watched a U-Tube video that described how to change out the hinges. The trick is find out how to lift the top panel on the washer to access the screws that anchor the hinges. Use a putty knife and slide it into the space between the top panel and the front panel. Got the job done today in an hour or so. Chose to also wipe out the top of the wash tub at the same time so it took a bit longer. Works fine now. Just like new.

Machine out of balance; banging; hopping.

  • Customer: Gary from Wellington, FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed very detailed instructions posted on the website. Made a difficult job possible; without instructions would not have been to do repair. Thanks to those who posted step-by-step process. Suspension springs most difficult part of job, followed by C clamp. Lots of sharp edges to cut and scrape your arms and hands. After seeing how this machine is built, I am done with Maytag appliances.

Washer was off balance

  • Customer: Daniel from Fort Walton Beach, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Cause:The main problem was the snubber ring got destroyed from continuously overloading the washer. That lead to the unit becoming off balance which in turn broke the belt pully off of the water pump and wore out the tub springs. Solution: Procedure 1: Make sure to turn off the water going to the machine, unplug the hoses and the power cord and if you have room take it out away from the wall. even after it is drained there will still be some water in the unit so keep a good size towel on hand. The pump is the easiest part to replace; simply lay the machine forward so that you can get to the back panel and the bottom at the same time. Remove the panel and the pump is just inside. remove the belt from the bottom of the unit then remove the black hoses from the pump taking note how they are situated and the size difference. Remove the bolts that attach the pump to the housing then lift the pump out through the opening; unless you have purchased new bolts you are going to want the old ones for the reinstall since the new pump probably doesn't come with any. Also, the replacement pump may not have the same mounting bracket but it will mount just fine without it. now simply install your new pump in the same position as the old, secure it to the housing and reattach the belt. Procedure 2: Now for the springs; this is a little more difficult and it is going to take some muscle and patience. Do not remove all of the springs at once, trust me! lol! The easiest way to do this is to remove one spring at a time and replace it with a new one; just make sure to mark them as you go or at least remember where you started. Only a few of them are accessible from the panel in the rear but if you tilt the machine back upright the whole front of the machine can be removed very easily. First you must remove the top; to do this there are two brackets on the back at the top behind the instrument panel that can be removed with a Phillips head screw driver. after they are removed pry the front of the whole top panel up, there are only two brackets holding it down. Remove the two screws that you have uncovered at the front and remove the front panel by lifting up slightly and pulling forward. you can now get to the rest of the springs. Take note how everything was removed and reverse process to put it all back together. Thanks and goodluck!

during certain wash cycles their was a burning rubber smell.

  • Customer: Jeff from Cornelius, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
lifted the front of the washer on a 45% angle,leaned it against the wall and gained access to the bottom and the belt,rolled the old belt off,it was very stretched came off easily,rolled the new one on and that was it.

The problems only put the Belt in back

  • Customer: Syed from Mcallen, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
The water pumps was was very easy to put it back in and I Save money And they have a video instruction to put it back in water pump This is a first time I repair something myself Everything was very helpful :)

Lid Would Not Stay Up

  • Customer: michael from blanchester, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took of lid,took out screws,put on hinge and pins,simple job

Agitator Broken

  • Customer: Barry from Spartanburg, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Replaced agitator in less than 30 minutes with ratchet and socket. Fast delivery from vendor. We are up and running again!! Very pleased.
All Instructions for the PAV2300AWW
451-465 of 627