Switch to Classic
Models > P3314 > Instructions

P3314 Chainsaw - Instructions

All Instructions for the P3314
1 - 5 of 5
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Both the Fuel line and the Engine fuel line, where dry rotted.
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines.
2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fall into the path of the new fuel lines installation.
4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor.
5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line.
6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary.
7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
Parts Used:
Fuel Line Tank Purge Line Engine Fuel Filter
  • Victor from SCOTTSVILLE, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
15 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fuel and Purge lines had disintegrated
Disassembled it and cleaned fuel tank. Cut and ran new fuel lines, installed filter and reassembled. Parts fit perfectly and got running after not running for over 20 years.
Parts Used:
Fuel Line Tank Purge Line Engine Fuel Filter
  • Casper from ERATH, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worn out oil pump/burning chains
After checking several different videos, ordered the repair parts and two specialty tools( Clutch removal/install and a worm drive remover/installer) Total for parts and tools around 45.00. Much cheaper than the shop wanted, 85.00 to look at it plus parts. As for results I've used the chainsaw all afternoon no problem. Runs like it did 12 yrs ago. Pumps oil the would make Jed Clampet proud
Parts Used:
Assembly-Oil Pump Gear-Worm Spring
  • William from EVANSVILLE, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not start , had been sitting for years,
I did not write detail steps , basically remove old carb replaced with new one, reassembled started right up no adjustments were needed !
Parts Used:
Carburetor
  • Sherri from BREAUX BRIDGE, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke the original ring
Took chainsaw apart and replaced the ring.
Parts Used:
Ring - Piston
  • Danny from STEVENSON, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the P3314
1 - 5 of 5