NVL333EY0WW Hotpoint Dryer - Instructions

First I unplugged the dryer, then I removed the access panel on the back of the control panel. I removed the wires from the back of the switch...Here is where I messed up. I removed the switch prior to ordering the part, the bad part is the way I removed the part. When you get the new part in you will be able to see how it will be mounted to the control panel. I had no idea, so I did what was necessary to remove it. Needless to say, I bent the hell out of the hole that the switch mounts in. In turn, the installation of the new switch did not go as easily as I would have liked. After straightening out some metal and drowning the thing in epoxy, the new switch is installed. I hooked the wires back up on the back of the switch, plug in the dryer, and dry some clothes. Standing victorious over the dryer with beer in hand, not only did I accomplish the mission but I learned my lesson... destructive removal = BAD!

The switch made a humming sound when I turned it so I thought that might be the problem. Using the instructions on this Web site I took the top panel of the dryer off (after unplugging it), unplugged two wires leading from the switch (needed pliers for this), and removed the switch unit by rotating it counterclockwise (when behind it).
The replacement part came in two days. The installation went a lot quicker-maybe ten minutes.

unscrewed the back plate off of the dryer. Disconnected the the wires off of the switch. Remember to to unplug your dryer from the wall first!!!. Reconnect the wires to the new switch and twist back into place. Be careful not to bend the metal tabs. Put the back plate back on and plug in. Put on new knob and the wife was smiling. Took about 8 minutes to repair.

a. researched internet to find how to access rotary starter switch
b. isolated all electrical input at breaker box
c. removed 4 torx screws on top of dryer head
d. lowered dryer head (swivels toward front)
e. pulled electrical connections from back of switch
f. turned and pulled thus releasing rotary switch
g. reversed procedure above
h. reconnected electrical
i. started dryer - it worked first time
j. watched football until wife came home
k. told wife dryer was fixed and what a bear it was to get it done :o)
l. that night accepted my reward for working so hard at fixing the dryer and saving us a bundle. :o)
m. now we are both smiling

Troubleshooting was the hardest thing to do in this repair. the first thing I found wrong was the thermal overload was bad. That was easy to replace since that is on top of the housing for the heating coils and easy to reach. Only 2 screws hold it in place. Once I replaced that the dryer would start but, the temperature was off the chart. Now I know why that part broke. The control Thermostat was a little harder. That is held in by 2 screws but it is in an awkward place. I replace the 2 slotted screws with nut driver type screw which made it easier to place the screws in such a small area. Once the control thermostat was replaced the dryer worked great

Removed front and top panals to dryer. Installed belt over the drum. opened back air vent panal and installed belt to pully. Reinstalled back top and front panals. Done.

My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.

Watch the videos for replacing the belt. The one by Kenmore is the most accurate even though it isn't GE -- the mechanisms are the same. Here is the link to the one I found most helpful: https://www.youtube.com/watch?v=G2wTmfurT5o

First: You don't need to pull the washer/dryer out at all. Leave it in place. You can put the belt around the drive shaft and get the tension pully in place by feel and inspect your work with a flasklight,

Second: There is absolutely no reason to spend $70 on a rubber belt. Other places sell it as cheaply as 10 dollars. Shop around -- the actual part is not at all impressive and should not be priced this high.

On arrival at rental in Florida, knob & half of shaft are on top of the dryer. Thanks! It's fixed

My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.

Removed four allen head screws to expose inside of panel. Used flat blade screwdriver to raise spring retainer and turned switch counter clockwise to remove.

installation exactly how your directions told me on the computer

Removed top panel from dryer. Unplugged the 2 wires for swithch, rotated swith, and removed. Reversed the process. Put parts back together.

I like to fix , i have time and i just give me the chance to try , and i did it , i wish to pay less for the parts , but was a good feeling when the problem fixed

I turned off the power, unscrewed the 4 screws from the top of the dryer. I then opened it and turned the switch that was in there counterclockwise exactly as utube video said to do. I then took off the two wires from the old switch. The rotary start switch fix right in where the old one was. I put the panel back together, put on the old knob and turned the power back on! It took less than 15 minutes from start to finish! If I can do it anyone can! Joanne Klinkhammer Cecil, Wisconsin