Quick Question!

Have you ever purchased from PartSelect.com before?

Models > NFW7200TW10 > Instructions

NFW7200TW10 Amana Washer - Instructions

All installation instructions for NFW7200TW10 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the NFW7200TW10
61-75 of 92
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door Lock Latch

  • Customer: PAUL from FLUSHING, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
The product came on time and was perfectly rapped , it took me 15 mins to install after watching you tube videos on front loader washer . I was happy I didn't have to call a service man in . . . .

Door Lock Latch Broken Inside

  • Customer: Chris from North Reading, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy repair, once I read the reviews and watched a couple of you tube videos. I just released the band holding the gasket in place, pulled it back, unscrewed the latch and installed a new one. Less than a 10 min job. I am glad I found this web site, thanks guys!!

Washer shaking on spin and spin speed low.

  • Customer: Byron from Bellaire, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I simply followed manufacturers direction from the service manual that I had purchased. I removed the cover from the back of the washer, removed the old belt and put the new belt on. The old belt was certainly stretched and putting the new belt on simply required that I walk the new belt on to the pulley and then adjust the belt to the center of the pully. The end result was a washer that now spins as it did when new.

Broken latch on front of washer

  • Customer: Brenda from Citrus Heights, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took both the screws out on the top back. Lifted up the back about 1/2 inch and slid to the back. Reached into the front of the washer where the latch was connected. Disconnected the 3 wires (plugs) attached to the latch, took out the 3 screws located inside the washer door. Took a second person just to hold the latch and bring it out after the screws were off the front inside the washer door. Put new latch in, connected the wires, put in the screws behind the washer door (3 of them) and slid the top into place and put the screws in the back. Takes longer to tell you than to do it. Remember the screw on the left side front (top) as you face the washer and remove that screw. The plastic had disintegrated on mine but am not going to replace that part until I have to.

door lock broke

  • Customer: vicki from westhope, ND
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again

Was not draining

  • Customer: Mary Ellen from Waconia, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Purchased the pump from PartSelect after reading other reviews and let me tell you....it works great now. Way cheaper than hiring a repairman.

Drain pump

  • Customer: Kimberly from Clinton, MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took back panel off. Replaced the drain pump

Outside door broke at hinge on front load washer

  • Customer: Jeff from Tunnel Hill, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Service repair tech ordered the outside door part and the door safety piece. (plastic shield that covers the glass inside door.) Outside door piece came in within week. Could not get other part in (backordered). Found online and had it within 4 days. Two screws hold hinge on to washer front. After removing hinge screws, pick up on door to clear the tabs on back of hinge through the tab holes in the back hinge brace. (This does not have to be removed. After removing door, unscrewed all screws in back of door to disassemble. Removed hing from hinge slots on door front and inserted into new door hinge slots. Snapped new door safety onto back of new door front by aligning tabs on door safety and outer door piece. Replaced glass bowl and door back by replacing screws in screw holes and tighten. Reattached door by inserting tabs on back of hinge into tabs on washer front and tightening hinge screws.

The latch was broken so that the front door wouldn't close.

  • Customer: Jennifer from Staunton, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

Washer would not drain nor spin

  • Customer: Tracy from Danville, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
My husband read on the Internet how common this problem is and how easy we could do it ourselves rather than pay the service etc.... While reading there was a link for Part Select. We simply found the part with-in minutes and ordered. They have PayPal so I basically ordered it in less than 1 minute, emailed my receipt and DONE! We selected overnight shipping because the laundry was piling up - we received the part less than 24 hours and I was up and running before dark! PERFECT!

Odd noise when the spin cycle started, water would not drain, D5 error.

  • Customer: Anthony from Holbrook, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The washer comes up with the D5 error if either the door is not shut correctly, or it can not detect that the washer is drained. I had to put the washing machine on its side to access the bottom. There is an access hole that you can get the pump from. I unplugged the pump, then removed the bolts to take it out. The pump comes apart with a few screws removed. I saw that the magnet inside was broken in half. Putting a new pump back in solved the issue.

drain pump runs continuously

  • Customer: Joe from Greenfield, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Checked owners manual for diagnostics. Pointed to door lock mechanism, so we replaced. didnt work. Went online to Just Answers.com, chatted with pro named Mike(for the fee of $25) and without getting full description, he told me to replace pressure sensor. Bought one here for $50, replaced it, and still the problem lingered. Called a real Technician to the house, for $90, and he spent 4 minutes looking and tapping, and voilla, it worked. Turns out it was a stuck relay on the control board, and the tapping loosened it. He told me I may have trouble with it in the future. If so, I would buy one here. Thanks

I was getting an "nd" error code with every wash cycle.

  • Customer: Timothy from Bismarck, ND
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the back service panel and checked the drain hose for any debris and checked the connection from the tub basin to the drain pump. I then check the drain pump and noticed the impeller blades were a bit worn. After the new drain pump arrived, I did have to swap the old intake housing with the new one in order for the whole thing to mount to the shock-absorbing mounting plate. Reconnected both hoses and the electrical connection and everything ran great!

Hot water would not shut off when wash temperature selected was hot or warm.

  • Customer: William from Charleston, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power cord. Shut off water supply. Disconnected hot water supply hose. Removed top cover. Disconnected appliance connection to Hot Water Control Valve. Removed screws holding HWC valve. Removed existing HWC valve. Installed new HWC valve. Reconnected appliance connection. Reconnected water supply hose. Turned on water to check for leaks. Reconnected power supply. Started washer with hot cycle selected. Timed water fill time. Replaced top cover. Washed a load of whites in hot water. Installation and test complete.

it does not do anything. It does not work at all.

  • Customer: Ricardo from Rockwell, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the part.
All Instructions for the NFW7200TW10
61-75 of 92