Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MZD2665HES > Instructions

MZD2665HES Maytag Refrigerator - Instructions

All installation instructions for MZD2665HES parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MZD2665HES
631-645 of 832
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Inoperative Icemaker

  • Customer: Earl from Belhaven, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed malfunctioning icemaker and discovered that inlet water line was frozen. Thawed line using hairdryer and problem resolved. Returned new icemaker to PartSelect they promptly credited my credit card account. Problem solved.

The ice maker stopped making ice & leaked

  • Customer: Robert from Sacramento, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I discovered that the water inlet was freezing, then the incoming water would run into the tray. I watched the video, then removed the ice maker. I discovered the the top two screwed just had to be loosened, not removed. I removed the bottom screw and move the ice maker to the side to disconnect the wiring harness. I found it to hard to disconnect. The pinch clips did not depress as they were supposed to, but the finally release. I did the replace without unplugging the refrigerator and it went fine. Took less than 15 minutes.

Old ice maker hanging up

  • Customer: Anthony from Mountain Home, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed and inspected the old unit and found the tray coating was flaking off. I ordered the new ice maker on line, One screw and rotate unit counter clockwise about 10 degrees unlocked it from the two snap in mounts. then unplugged the wire harness and it was free. Had to put the short wire harness on new unit, reverse removal steps and it is completed and working fine.

Ice machine was not making ice

  • Customer: William from Grafton, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Changed the ice and Water filter, works great...

Light switch broken off by container in freezer

  • Customer: Michalynn from Powder Springs, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Ice maker stopped dispensing ice.

  • Customer: George P from McKinney, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Ordered the correct replacement part (Icemaker Auger and Crusher Blade Assembly) as found here at PartSelect.com. Part was delivered within two days. Removed two screws to remove the old assembly; inserted new assembly, replaced the screws and problem fixed. Couldn't be easier.

Water dispenser was flowing very low

  • Customer: Carlos from Tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Replaced water filter head. Very easy to do. Make sure that you also have a bucket so that you don't spill water everywhere when you disconnect the water line from the fridge.

Auger quit working - wouldn't dispense ice

  • Customer: Sara from Walsenburg, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old auger unit by removing two screws - installed new auger unit by replacing the two screws. Easy schmeasy!

Water was dripping into ice bin as long as icemaker was activated (bar lowered)

  • Customer: Derek from Murphy, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Based on comments I read at this web site, I first ordered the water valve; that did not fix the problem. Replacing the icemaker did fix the problem. It was easy to replace. Contrary to the instructional video, I couldn't simply tilt out the icemaker at the bottom after removing the lower screww; I had to loosed the two top screws as well. The leak was caused the coating on the icemaker being cracked and peeling.

water was leaking from the valve.

  • Customer: jim from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
After watching the video on your web site the repair was very easy. It took only 15 minutes to replace the valve.

ice maker not making ice

  • Customer: George from Sedona, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video which gave me confidence that I could do the repair which I did in very little time. One thing to emphasize though: When you remove the vertical wire connector from the back of the freezer compartment, remember which color wire is on the top. I needed to watch the repair video a second time to be able to make that determination. Probably the repair video should have mentioned keeping track of that connector regarding the re-connection of it because it could also connect when turned 180 degrees.

Ice Maker wouldn't make Ice

  • Customer: Michael from Ventura, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched a youtube video and completed the repair in less than an hour from start to finish and save myself a service charge. It was fairly easy, the only problem was that it was a bottom freezer and getting to the ice maker was harder than if it was a side by side or top freezer.

The dual water valve had been broken in a move

  • Customer: Gary from Denver, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I order the part from Part Select and watched "How to Replace the Dual Water Valve" video that was offered on the Part Select web site. I followed the process and easily replaced the part. I was quite pleased with the service from Part Select.

Leaking icemaker

  • Customer: Annette from Peoria, IL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I used the video on your website. It made me feel very satisfied that I was able to do it myself!

Ice maker did not work any more.

  • Customer: Mustafa from Philadelphia, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I unplugged the fridge. Then I removed the ice bucket. Then I removed the ice maker using a 3/4 socket to separate the connections and then used a small screwdriver to separate whatever connections were left. Then I installed the new ice maker and checked its level. Everything now works fine.
All Instructions for the MZD2665HES
631-645 of 832